WHot-dip Aluzinc Steel Building Roof Walls
- Ref Price:
-
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 34343 unit
- Supply Capability:
- 3434 unit/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
1. Description of the Hot-dip Aluzinc Steel：
Hot-dip aluzinc steel structure is composed of aluminum-zinc alloy, consisting of 55% aluminum, 43% zinc and 2% at 600 ℃ silicon solidification temperature and composition, the entire structure is made of aluminum - iron - silicon - zinc, to form a dense quaternary crystals an alloy.
Hot-dip aluzinc steel has many excellent features: strong corrosion resistance, is three times the pure galvanized sheet; zinc surface with beautiful flowers, can be used as a building outside board.
Applications of hot-dip aluzinc steel:
1)Building: roof, walls, garages, soundproof walls, pipes and modular housing.
2)Automotive: muffler, exhaust pipes, wiper accessories, fuel tank, truck boxes, etc.
3)Appliances: refrigerator back, gas stove, air conditioners, microwave oven, LCD frame, 4)CRT-proof band, LED backlight, electrical cabinets, etc.
5)Farm: barn, sheds, silos, piping and other greenhouse.
6)Other: breaking heat insulation cover, heat exchangers, dryers, warm water, etc.
2.Main Features of the Hot-dip Aluzinc Steel：
• Excellent corrosion resistance
• High temperature oxidation resistance
• High hot reflectance
• Good manufacturability
•Beautiful appearance
•Surface coating
•Cost-effective
3.Hot-dip Aluzinc Steel Images
4.Hot-dip Aluzinc Steel Specification
AVAILABLE SPECIFICATION
HOT-DIP ALUZINC STEEL COILS | |
THICKNESS | 0.16mm-3.5mm |
WIDTH | 1250mm MAX |
COATING MASS | |
SPANGLE | Regular Spangle, Minimized Spangle, Zero Spangle |
SURFACE TREATMENT | Chromated / non-chromated, Oiled / non-oiled, Anti Finger Print |
COIL INNER DIAMETER | 508mm or 610mm |
HOT-DIP ALUZINC STEEL COILS | |||
COMMERCIAL QUALITY | ASTM A792M-06a | EN10327-2004 | JIS G 3321:2010 |
STRUCTURE STEEL | SS GRADE 230 SS GRADE 255 SS GRADE 275 SS GRADE 340 SS GRADE 550 | S250GD+AZ S280GD+AZ S550GD+AZ | SGLC440 SGLC490 SGLC570 |
5.FAQ of Hot-dip Aluzinc Steel
We have organized several common questions for our clients，may help you sincerely：
1.What advantages does your company have？
Cement : Annual capacity of 400 million tons, No. 1 in the world
Fiberglass: Annual capacity of 1 million tons fiberglass, No. 1 in the world.
Composite Materials — Carbon Fiber: Annual capacity of 10,000 tons PAN precursor and 4,000 tons carbon fiber, No. 1 in China
Composite Materials — Rotor Blade: Annual production capacity of 15,000 pieces, No.1 in China, Top3 worldwide
Glass: CNBM owns about 20 modern float glass product`ion lines, With annual capacity of 10 million square meters glass.
Light Weight Building Materials: Annual capacity of 1.65 billion square meters of gypsum board, No. 1 in the world.
Commercial concrete: Annual capacity of 0.35 billion cubic meters, No. 1 in the world.
Refractory Material: Annual capacity of 40,000 tons casting refractory, No.1 in the world.
- Q: I'm considering a Massey Ferguson model 90 front-end loader for sale, to attach to my Ford 2000 tractor. How can I find out before buying if it will fit my tractor?
- Most likely your local New Holland dealer will not know. If you plan to attach it yourself , good luck. What I would do is take it to my local mechanic that works on anything. He will most likely have to buy additional bolts , cut the metal , and weld it in different spots. Then there is the hydraulic hookup. I have 2 tractors with front end loaders with the hydraulic fitted to existing remotes which makes it a pain to use the front end loader or pull a disk at same time. The Ford 2000 is a 20 year or older tractor and has one set of remotes at most. If the Massey Ferguson front end loader has one hydraulic to lift the front end loader and another hydraulic to use frount bucket, fork , or whatever, you will need add another set of remotes to the Ford 2000 or have a (do not know the exact name of device) splitter to mount on tractor so to have two hydraulic functions from 1 remote which can get expensive(over a thousand bucks here in splitter). Hope I made this clear.
- Q: i have ckecked all hoses and fluid level . when i try to raise lift it tries to lift but it is already at the top . i push lever to go down and nothing happons
- Assuming you mean the two (left and right) lower lift arms that comprise the 3 point hitch. Also assuming that there is no implement presently attached to these two lower arms and the top link. Further assuming that you have 2 levers that control the lift arms (one lever controls position and the other lever controls breakout draft effort), both of these levers must be in the down position which is generally forward (toward the front axle) on most tractors. Finally, on some tractors, the weight of the two arms is insufficient to go down with the force of gravity alone, and this is more often seen with brand new tractors. So assuming that you have done all the preceeding then simply go to the rear of the tractor with engine off and two levers forward and stand on one of the lift arms. It should go down. If this fails, then it is possible that hooking op the hydraulics for the front end loader was done incorrectly if problem did not occur until after installation of front end loader
- Q: so I just got a invert mini and my loader is a empire halo too, well whenever I try to put the loader in, I have to literally stuff the thing, and when I get it in the clamp on the feed neck doesn't close! should I just buy a new loader or what!
- Sand the Halo's feedneck down a little. Use a sheet of coarse grit sandpaper, place in your hand. Wrap the feedneck with it, then twist in even motions. Do that for a minute, wipe it off with a rag (or blow the shave dust off) then test the fit. Repeat as necessary. Once it's sanded enough to your preference, use finer grit sandpaper to smooth the neck out, then clean it up with a rag.
- Q: Liugong ZL50CN loader, how much do you buy?
- We have more than 320 thousand points to buy a dozen of the basic stage to spend 2 million bucks.
- Q: What is the loader divided into 20,30,50?
- Refers to the carrying capacity, for example, 50 forklift truck is 5 tons of load, 30 is 3 tons
- Q: I have an International-Hough Crawler loader from the 70's and I have been moving bark and log scraps with it for a day and a half after having it sit for a year and a half. I had to jump start and charge it to get it out of the shed, I put in all new motor oil, 20 gallons of hydraulic oil, and 20 gallons of diesel. After running it for a day and a half the tracks will not pull the weight of the dozer it feels like, and the dozer will barely turn and when it does the tracks completely seize up. Any ideas or suggestions of what could be wrong or any possible fixes. Considering trying to change the fuel filters on it because they have been on there since the late 90's, I'm not sure wether this will solve the track problem but I hope it will enhance the engine performance.
- There is normally hydraulic filters that need to be changed also. To me it sounds like wet clutch pack porblem
- Q: What about the high loading and unloading capacity of Baidu 50 loader at 30?
- 50 loader handling height generally above 290, 30 do not know
- Q: hey please help me i want to install back up loader channel to play discs which are of different versions :'( plzz help me plz i hav spent alot :'( already i already hav homebrew installed :'(please help me :'( i beg u
- To use a channel, you have to install the loader first. If you already have a loader installed, than just find the forwarder for that loader and use Wad Manager 1.7 or Multi Mod Manager to install the channel
- Q: i make my own muzzle loaders.. out of all kinds of wood.. hammer and flintlock... i carve all kinds of desings in them and stain the wood.. how much do you think they are worth?
- Without actually seeing one how can anyone give a price? I could say, I make doghouses, using all types of wood and carve designs in them, how much do you think they're worth. Would you know?
- Q: 50 loader plus long arm, the main purpose is to do ah? More detailed, thank you
- Can give higher auto feeding, such as the Dragon King can give 30 high relief Shuangqiao auto feeding, there is the object hanging higher, but because it is a plus the long arm, so increasing the length of the vehicle, there are some limitations, but basically ignored
Send your message to us
WHot-dip Aluzinc Steel Building Roof Walls
- Ref Price:
-
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 34343 unit
- Supply Capability:
- 3434 unit/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords
