Special truck tail lift--DC-003 - micro pygidium
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1 unit
- Supply Capability:
- 1 unit/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
![]() |
![]() |
The micro pygidium is installed in the end of the van,business car,carrying 200-500kg, convenient for the action inconvenience prople to lifting the wheelchair, or use for the car go out works up and down the goods,installation just need a few space at the end of the car,portable and easy to use. Folding pygidium is installed under the crossbeam at the end of car,in the place Folding Tailboard::Installed below the girder on the tail of the automobile, in places without the use of the tailboard, it doesn’t need operation, namely it doesn’t affect normal opening and closing of the rear door of the carriage. ※If you need to order tailboard, please provide the brand, tonnage and power supply of trucks, accurate data of B, D, E, H and L in the chart, cargo type and handling operation mode, so that we select the optimum tailboard model and specification for you. |
Related Products |
- Q: Which mobile shear fork lift is better
- Mobile shear fork lift There are four major systems, The mechanical structure system,
- Q: How does hydraulic platform change sealing ring, how to operate
- Dismantled after checking in parts, parts should be stored in a clean environment, and add to prevent knock against the isolation device, with professional pliers to take out the seal, after installing the new seal, again before assembly, parts should be cleaned.
- Q: What can be done when the hydraulic platform is down?
- The left and right sides are connected by wire rope, while the other side is synchronized.
- Q: How to automatically lift up and lift
- There is a manual lifting table, with the hand rotating black knob, lifting the platform clockwise, reducing the counterclockwise elevation.
- Q: There are several reasons for the hydraulic cylinder oil leak on the elevator
- Oil cylinder in and out tubing joint cracking; (I've seen a lot of this in practice.) 2) the sealing damage of the piston rod with the piston rod is caused by the pull of the piston cylinder. 3) cooperate with cylinder liner piston rod out end seal is damaged, this is caused by long-term use of seal aging more, also has a lot of end cover on is too hard to seal extrusion is damaged, there is a lot of domestic manufacturer of hydraulic cylinder design is not reasonable cause (mostly in order to save costs)
- Q: There is no elevator on the 7th floor of the home to install a lift or lift
- All manned lift, lifting platform, moreover, to pass through security, common theory suitable equipment can't be through security inspection, after you installed the safety bureau will let you immediately removed. These things are too low
- Q: What is the difference between elevator and elevator
- It's the same, but everyone's understanding is different.I hope my answer will help you.
- Q: How to use the elevator to be safer and more efficient
- Annual maintenance Check all hydraulic pipes and connectors. The pipe shall not be broken, the joints shall not be loose, and all the joints must be tightened. Remove and disassemble the descending valve, blow the plunger through compressed air, then load and resettle. Remove the hydraulic oil, remove the oil strainer and remove the oil strainer, clean it up and then put it back in the tank. Be familiar with 'ten notices' 1, pay attention to the agencies should regularly check and adjust the brake of the brake and the clearance between the brake wheel, flexible and reliable. The clean surface, there should be no dirt, in case of dirt must wash with gasoline or thinners. 2, pay attention to removing the hydraulic tank of fuel cap, remove the cap around earth, unscrew the cap, remove residual impurities in the joint area (not rinse in order to avoid water seeping into the tank), confirmed to open the cap. 3, pay attention to the elevator remove the hydraulic tank of fuel cap, filter cover, test hole, hydraulic tubing parts, cause the system oil when exposed to avoid dust, remove the parts to open completely clear before first.
- Q: The automatic mahjong machine has a lift station always one. What is the other three normal
- There are two main reasons for this: In the ascent of the aluminum plate, the interference with the limit mechanism
- Q: What is the imported hydraulic platform car? Kneel and beg your help
- Their platform has a special mechanical structure that is widely used in high-altitude work, the shear fork structure, and the higher stability after lifting and lifting
Send your message to us
Special truck tail lift--DC-003 - micro pygidium
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1 unit
- Supply Capability:
- 1 unit/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches