Socket Spigot Tee

Ref Price:
Loading Port:
China Main Port
Payment Terms:
TT or LC
Min Order Qty:
1 Ton m.t.
Supply Capability:
6000 Tons per Year m.t./month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

1. Lost foam casting technology.
2. Standards ISO2531, EN545, EN598 and BS4772
3. Ductile iron
4. ISO 9001 Certificat
1. Material     Ductile iron

2. Technique   Lost foam casting technology (It is the most advanced technology in this field, so the quality of our products is much better than those using traditional casting.)
3. Standards   ISO2531 / BS EN545 / BS EN598 / BS4772
4. Certificate  ISO 9001 2008 and BV Product Conformity

5. Size       DN80-DN1400

6.Internal linings
No internal linings
Portland cement/ high alumina cement/ sulphate resisting portland cement/ resistance hydrochloric cement lining in accordance with ISO 4179
Zinc coating plus bitumen painting
Epoxy coating
Fusion bonded epoxy coating
External coatings
No external coatings
Zinc coating plus bitumen painting according ISO 8179
Metallic zinc with finishing layer
Epoxy coating
Fusion bonded epoxy coating
7. Thickness of wall   K9 / K12 for ductile iron pipes
K12 without branch / K14 with branch for ductile iron fittings
8. Flange drilled     PN110/ PN16/ PN25 according to BS4504
9. Socket joint      T type ( push-on type) / K type ( MJ type)

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:Will the moving angle of the air conditioner indoor be harmful to the connecting pipe joint?
There's nothing wrong with the moving angle. Our unit air conditioning because moving, we have been disassembled and assembled several times (copper tubes are disk, installation and then stroke straight), there is no leakage problems.
Q:Is the trachea connected directly to the inside and outside threads? I remember a sealing ring
The question is too abstract:#1: if the pipe thread (G, NPT, BSP), only need to use raw tape or liquid TEFLON coated, tighten can be.#2: some joints are sealed by the cone. Sealed by a cone (of a ferrule); some have O rings, others are straight. You can find it on PARKER's product samples.#3: some connections are screwed with M thread. Seal by type O ring or copper gasket. You go to FESTO, SMC's website to find the M thread connector, you can.#4: there are other types of fast couplings, too. There are too many kinds.
Q:PVC how to deal with leaking water in the upper opening of three pipe joint of launching pipe?
To buy a bottle of UPVC dedicated glue, and then go to the production of PVC pipe manufacturers, where they want a little PVC resin powder
Q:Very confused about the pipe fittings and the fittings, and can not distinguish them
The task is accomplished by the joint body, one end of which is connected to the pipe joint and the other end connected to the device
Q:What's the difference between the half pipe joint and the branch seat?
The 2. branch pipe seat is widely used abroad in recent years, the branch for strengthening pipe connection, to replace the traditional use of different diameter three, reinforcing plate, strengthening pipe etc. branch connection type, which has the advantages of safety, lower cost, simple construction, improve media channel, standardization, series design has the advantages of convenient so, especially in high pressure, high temperature, large diameter and thick wall pipe is widely used, instead of the traditional branch connection method
Q:What is a reinforced pipe joint?
The strengthening pipe joint is a medium strength iron casting, which has good casting performance, simple process, small casting stress and no manual ageing
Q:The pipe line of the hydraulic pressure pipe is formally installed
2.2. common thread is used for the connection and fastening between the mechanical parts, and the general thread connection is mainly made of coarse thread. The thread strength of the fine tooth thread is slightly higher than that of the same nominal diameter, and the self-locking performance is better.Mark 3. metric screw thread: M20-6H, M20 * 1.5LH-6g-40, where M represents a common thread metric, 20 nominal diameter thread is 20mm, 1.5 pitch, LH said, 6G 6H left, said thread precision grade, precision grade of internal thread uppercase, lowercase precision grade of said external thread, 40 screwing length;3.1. commonly used metric ordinary coarse thread pitch as shown in the following table (threaded hole diameter: carbon steel = nominal diameter P = nominal diameter cast iron; 1.05~1.1P; processing thread rod diameter = nominal diameter: 0.13P):Table 1 diameter / pitch of common metric coarse tooth threadThe nominal diameter of P cast iron bottom steel bottom thread rod diameter pitch P cast iron bottom bottom rod diameter of external thread steel
Q:Drawing design, drain cross dry pipe is flexible cast iron pipe, vertical pipe is PVC pipe joint
The transverse drain pipe is a flexible cast iron pipe. The vertical pipe is PVC pipe joint. When it needs to change the diameter, it is most suitable to use a special AD type bottom joint.
Q:What is the nominal diameter of the phi 1/2 in the pipe joint?
1 inches =25.4mm.1/2 "- 4 thiophene, 3/4" - 6 thiophene, etc..Pipe, pipe thread and machining are often used in these old units, but they are not legal units of measurement in our country.Installation industry and business are commonly used in this unit.
Q:PPR pipe joints did not plug in the melt, in the end will leak?
1, pipe and pipe fittings should be adopted hot melt essentials, not allowed in the pipe and pipe fittings directly to the wire, and metal pipe can flange connection, and with water device connection, must use metal insert pipe fittings;2, the construction of hot melt connection must use the quality of reliable hot-melt equipment to ensure the quality of welding;3, the use of special scissors cutting vertical pipe shall be smooth without burr, argot;4, clean welding pipe fittings, the quality of sand, dust and other restraint damage are discussed; and the heating head is welding material inherited size related firmly in the hot melt machine, connected to the power supply, heating temperature to reach the best looking head;
Takes customers' satisfaction as our goal, we contribute to our environment and society. Our company has a team of competent technicians and skilled workers, and wins customers' excellent promise and honor of the society because of good quality and satisfied service with six years' development. Our commitment to quality will ensure the continued success of our company.

1. Manufacturer Overview

Location Shandong,China (Mainland)
Year Established 2006
Annual Output Value
Main Markets Eastern Europe
Southeast Asia
Mid East
Eastern Asia
Western Europe
Company Certifications ISO9001:2008;BV Certificate For Product Conformity;China Credit Example Certifitcate

2. Manufacturer Certificates

a) Certification Name  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage 71% - 80%
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size: 5,000-10,000 square meters
No. of Production Lines 5
Contract Manufacturing OEM Service Offered
Product Price Range