Small Injection Machine HXF65
- Loading Port:
- China Main Port
- Payment Terms:
- TT or LC
- Min Order Qty:
- 1 Set set
- Supply Capability:
- 3500 Sets per Year set/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Detailed Product Description of Small Injection Machine HXF65
Injection weight is 67 to 123 grams
Main specification of HXF65 | Screw A | Screw B | Screw C | Screw D | |
Injection Unit | |||||
Screw Diameter | mm | 28 | 32 | 35 | 38 |
Screw L/D Ratio | L/D | 24.3 | 21.3 | 19.5 | 18 |
Shot Volume (theoretical) | CM³ |
73 | 96 | 115 | 136 |
Injection Weight (PS) | g | 67 | 87 | 105 | 123 |
Injection Rate | g/s | 40 | 55 | 66 | 74 |
Plasticizing Capacity | g/s | 6 | 8 | 10 | 12 |
Injection Pressure | MPa | 229 | 175 | 146 | 123 |
Screw Speed | rpm | 190 | |||
Clamping Unit | |||||
Clamp Force | KN | 650 | |||
Toggle Stroke | mm | 270 | |||
Max. Mold Height | mm | 300 | |||
Min. Mold Height | mm | 100 | |||
Space Between Tie Bars (W×H) | mm | 310X290 | |||
Ejector Force | KN | 27.5 | |||
Ejector Stroke | mm | 65 | |||
Ejector Numbers | n | 1 | |||
Others | |||||
Max Pump Pressure | MPa | 16 | |||
Pump Motor Power | kW | 7.5 | |||
Heater Power | kW | 6.88 | |||
Machine Dimension (L×W×H) | m | 3.53×1.1×1.7 | |||
Machine Weight | t | 1.9 | |||
Oil tank capacity | L | 117 |
- Q:Want to know how to play a complete product, how to calculate the pressure, speed, etc.. Example, GREE electrical appliances series 4002B chassis, how can I transfer the full product?.
- After the injection molding machine has been installed, it must pass the strict debugging procedure, then can put into the official production. It mainly includes three parts, the whole machine debugging, the injection device debugging, the fitting device debugging and so on.(1) debug the whole machine performance1) check the hydraulic oil in the pressure tank and the oil in the lubricator to ensure adequate supply of hydraulic oil and lubricating oil. The model of the oil shall comply with the requirements of the manual.2) switch on the main power supply, switch on the master switch on the control box, and place the operation mode selector switch on the spot or manually. Start the injection moulding machine and check the running direction of the pump.3) the machine should be started under the condition of no pressure in the hydraulic system, and then adjust the hydraulic system pressure to normal pressure when it is started.4) after the hydraulic pump work, opens the oil cooler cooling water valve, carries on the cooling to the return oil, prevents the oil temperature to be excessively high.5) after the hydraulic pump works for a short time, close the safety door and then close the mold manually, and turn on the pressure gauge to see if the pressure is rising.6) when the car is empty, the manual operation of the machine is carried out by air several times, and the safety door, the indicator lamp and all kinds of valves are observed to be correct and sensitive.7) check relay, limit switch, counting device, total stop button is normal, reliable and sensitive.8) perform semi-automatic test run and automatic operation test, check whether the operation is normal or not.
- Q:Injection back pressure problem
- Five, the adjustment of back pressureThe adjustment of the injection back pressure shall be determined according to the raw material performance, drying conditions, product structure and quality, and the back pressure should be adjusted at 3-15kg/cm 3. When the surface of the product has little Qihua, mixed color, shrink and product size and weight changes, may be appropriate to increase the back pressure. When the nozzle leakage glue, salivation, Melt Overheating product decomposition, discoloration and feeding back too slow may be considered appropriate to reduce the back pressure.Back pressure is one of the important parameters to control melt quality and product quality in injection molding process. Proper back pressure plays an important role in improving product quality, and can not be ignored!
- Q:List of injection molding machines
- The best is Germany, Abog (formerly known as Albemarle, but by others to register the other German brand ARBURG): Baden Rumsfeld BATTENFELD;
- Q:What does injection pressure mean?
- Formation of back pressure in injection moldingFirst, the formation of back pressureIn the process of melting and plasticizing of plastics, the melt moves to the front of the barrel and more and more, gradually forming a pressure to push the screw back. In order to prevent the screw from backing too fast and to ensure uniform compaction of the melt, it is necessary to provide an opposite direction of pressure to the screw, which is the reverse pressure that prevents the screw from retreating. Back pressure is also known as plasticizing pressure, and its control is achieved by adjusting the oil return valve of the injection cylinder. Pre injection plasticizing screw injection molding machine is equipped with the rear end of the oil cylinder back pressure valve, regulating screw back when the injection cylinder oil cylinder speed, to maintain a certain pressure; shift speed screw motor after (resistance) is composed of AC servo valve control.Two, proper adjustment of the benefits of back pressure1, can melt inside the barrel compaction, increase density, improve the stability of injection quantity, weight and size of the products. 2. The gas in the melt can be extruded to reduce the gas, the inner bubbles and the gloss uniformity of the products. Slow speed screw back, so that melt inside the barrel full plasticizing, mixing and melting toner, color uniformity, avoid product color mixing phenomenon. 3, slow speed screw back, so that melt inside the barrel full plasticizing, mixing and melting toner, color uniformity, avoid product color mixing phenomenon. 4, appropriately increase the back pressure, can improve the product surface shrinkage and product periphery walk glue situation. 5. It can raise the temperature of molten material, improve the plasticizing quality of melt material, improve the fluidity of melt filling, and no cold glue on the surface of the melt.
- Q:What kinds of oil are used in the injection molding machine?
- 46# or 68# anti-wear hydraulic oilIn summer, use 68# anti-wear hydraulic fluid, 46# or 68# anti-wear hydraulic fluid.Domestic, the Great Wall, Kunlun will do is false too much, how long to change oil ah, lock cylinder with sub fuel tank, injection molding machine industry should use the most "run times", escape the oil in the air,. There are stamping, injection molding done, very few false.
- Q:Please tell me the reason for choosing this tonnageFor example, an injection molding machine, water flow of 4 tons per hour, then 4 units on the election of 20T cooling tower is not enough? 20T's cooling water flow is about 18 cubic meters per hour
- The cooling water machine 160T~200T injection dosage of 160T~200T injection molding machine cooling water consumption is 4.2 m fand /H.4, it is 16.8m /H that is not considered fand, injection molding machine mold water chiller, water and water machine water situation.A proposal to buy water tower could buy, if continued to increase the machine, it would have to change a small tower, currently selected tower selected points (nothing big cooling effect is better, too much waste), and the 20t tower and 30t tower much money.20t traffic to 15.62m /H fand tower25t traffic to 19.51m /H fand tower30t traffic to 23.4m /H fand tower
- Q:What do you mean by the number of beers produced by an injection molding machine?
- Beer here with the pronunciation of "sad", is the injection molding Hongkong said.The number of each beer translated into Mandarin is the first mock exam a few cavities, namely a number of parts injection molding means ~
- Q:Just boot time, storage time 19 seconds, after running an hour, 35 seconds are stored discontent, machine storage when the storage will stop for a while, what is the reason?When the material storage machine at the start of the normal storage is full, can, after a period of time running storage storage to storage half sit motionless, then stop for a while can move, the normal storage for 19 seconds, not normal discharge time can reach two minutes, sometimes can stop to rest
- According to your account, it is likely that the rear end temperature is too high, the feed port is bridged or the material is not broken
- Q:I want to know something about the purchase of high-end injection molding machinesCustomers in the whole power and hydraulic injection molding machine purchase process, those machine advantages, they are more concerned about, and if you choose to buy, then you will choose all electric or full hydraulic machine, why? To know a friend told me, we discuss together, thanked the boy in this
- I will choose hydraulic, full electric high cost, the main reason
- Q:The temperature of the injection molding machine: 1 220.2 210.3 200.4 190.5 175 period, when heated, everything is normal, but when the temperature reaches the set value of the motor work, work to about 15~20 minutes, 3 and 4 of the temperature began to rise slowly to 213~220 (lead injection unstable), other Dan normal. Then the motor is switched off, stop, about 15 minutes later, the 3 and 4 section temperature began to slowly fall to the set value, please master: what is the reason? How to solve?
- Hello:You can lower the feed rate a little, and there is a big wear on the material and the cylinder.
1. Manufacturer Overview |
|
---|---|
Location | Zhejiang, China (Mainland) |
Year Established | 2003 |
Annual Output Value | US$50 Million - US$100 Million |
Main Markets | North America South America Eastern Europe Southeast Asia Africa Mid East Eastern Asia Western Europe South Asia |
Company Certifications | ISO9001:2000;CE Certificate;ISO9001 Certificate |
2. Manufacturer Certificates |
|
---|---|
a) Certification Name | |
Range | |
Reference | |
Validity Period |
3. Manufacturer Capability |
|
---|---|
a)Trade Capacity | |
Nearest Port | ST.PETERSBURG,AMBARLI,RIYADH |
Export Percentage | 21% - 30% |
No.of Employees in Trade Department | 3-5 People |
Language Spoken: | English, Chinese |
b)Factory Information | |
Factory Size: | 50,000-100,000 square meters |
No. of Production Lines | Above 10 |
Contract Manufacturing | OEM Service Offered |
Product Price Range |
Send your message to us
Small Injection Machine HXF65
- Loading Port:
- China Main Port
- Payment Terms:
- TT or LC
- Min Order Qty:
- 1 Set set
- Supply Capability:
- 3500 Sets per Year set/month
OKorder Service Pledge
OKorder Financial Service
Similar products
New products
Hot products
Related keywords