Small Home Portable Ice Maker Outdoor Party Camping Ice Machine

Add to Cart

Place Order

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

You Might Also Like

Product size (mm) :310X230X325

Product Outer box (mm) :370X280X380

Product weight (net/gross) : 7.7/8.5kg

Product material: ABS plastic

Rated voltage (V) : 110/220

Volume (L) : 1.5

Product power (W) : 125

Ice shape: bullet shaped

Ice making capacity: 10-12kg /24 hours

Refrigerant: R600a

Note: each is individually packaged

Q: Ice machine is no ice, the pressure and current are normal: The evaporator temperature at about -20 degrees, such as ice the dripping water freezes, the ice bath, to ice, refrigeration heat pump shutdown, restructuring

Q: Ice machine has been in the state of ice, until downtime, how to solve?: The solution is as follows:Draw on a temperature control, a relay, 2 timers can basically get, but the timer timer range from 30 seconds to 40 minutes range. A timer is the time limit for ice retreat, which should be adjusted for 30 seconds, the other to 40 minutes adjustable, and temperature control, and to prevent temperature control when forced to retreat

Q: What is the stopping of ice in the ice making mechanism of the bullet making mechanism?: 3, ice machine is best to buy a better quality, in order to avoid accidents;

Q: Ice maker always has high temperature alarm. What's wrong?: 3. the ice machine enters the ice removal program (the water pump stops working and the compressor stops cooling), but the ice does not fall off.Fault reason: two way solenoid valve is damaged.Maintenance method: replace solenoid valve or outside ring.4., water shortage light, but the machine does not automatically into the water.Cause of failure: pipe water or water inlet, electromagnetic valve is out of order, valve is not opened.Maintenance method: check the water inlet of the pipeline, after the water is opened, restart the water. When the inlet solenoid valve fails, replace it.5. ice compressor compressor work, but the pump has not been working (no flow) failure: pump damage or fouling inside the pump plug.Maintenance method: clean the water pump or replace it.

Q: Ice maker is not automatically He Yuanyin: Five, ice machine leakage 1, the water inlet valve to supply water is too large. 2 、 the connection pipe is broken. 3, fault. 4, water level float valve fault.Six, noise is too big, 1, ice maker fan fault. 2, reducer fault. 3 、 compressor noise.Seven, water shortage alarm 1, water supply joint filter screen plug. 2, water pipe plug. 3 、 inlet valve block. 4 、 drain valve leaking. 5 、 water pump failure.Eight, boot system failure 1, phase sequence problems. 2, the power supply system failure. 3 、 control panel fault

Q: How do you use ice maker?: Ice maker using method:Ice making processBefore starting, you must check the automatic water supply device is normal, the water storage tank is reasonable (this machine has been transferred just when the water level, the user can not tune it).Plug in the power supply, ice machine began to work, first of all, the pump started running (water pump has a short period of exhaust air), about 2 minutes after the compressor started, the machine into the ice.

Q: Ice making mechanism prevents ice from falling properly: Fault reason: measuring water temperature probe fault, making intelligent control system can not effectively perceive water temperature and work, misjudgment, program error, or controller failure.

Q: How about water flowing ice machine not to pour water?: Is the solenoid valve out of order? Or an electromagnetic valve race. This problem may arise if the pump does not work.

Q: What is the reason shircore ice machine compressor does not work: 3. symptoms: compressor has been able to work, refrigeration, water pump has been working, pumping, ice continues to thicken, but always can not automatically enter the ice removal program, ice fall.Reason: measuring water temperature probe fault, so that intelligent control system can not effectively perceive the water temperature and work, misjudgment, program error, or controller failure.Solution: the multimeter is used to measure the temperature of the resistance probe (in the water temperature in the water tank near 0 degrees C, remove the control box of the three core lines, two lines on both sides of the resistance test), such as resistance in more than 27K, it was judged as controller bad, should be replaced, such as resistance of less than 27K and shall disconnect any two lines in a way, through the series resistance of the resistance to 27K to 28K.4. symptoms: the machine enters the ice removal program (the water pump stops working, the compressor stops cooling), but the ice does not fall off.Reason: two way solenoid valve is damaged.Solution: replace solenoid valve or outside loop.

Q: I want to build an ice factory next year and only make ice. Nissan 2 tons or so.What equipment do I need to buy? How much will it cost?: An ice machine directly. If you need to store the ice, you need a small cold storage, put a 10 tons, 20 tons.Produce 2 tons at one time, produce 6 tons in 24 hours.New direct ice making machine, about 120 thousand. The traditional salt water ice maker is almost 120 thousand.

Send your message to us

*Email

*TEL

*Quantity

*Unit