PVC Pipe ISO3505 Plastic Tubes

Inquire Now

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

pvc pipe
Water supply pvc pipe
Water discharge pvc pipe
Plastic PN10 and PN16 pvc pipe
DIN8077, DIN8078, ISO 15874 pvc pipe

Our pipes and fittings can be made according and conforming to the following International Standards:

1) American standard (ASTM Sch 40 & Sch 80, SDR 21, SDR 26, SDR41)

2) British standard (BS 3505, BS 5255, 4515)

3) Singaporean standard (SS 141, SS 272, SS 213)

4) Australian standard (AS 1477, AS 1415)

5) National standard (GB 10002, GB 5836, GB 14823, GB 13664)

6) International standard (ISO 4422, ISO 3633, IEC 614, GY 3050)

PVC Pipe Features

Non-conductive: Good insulation, assuring a safe system
Smooth surface: Small friction coefficient to ensure the cables go through smoothly
Fire resistance: Self-extinguishing, do not support combustion
Corrosion Resistance: Resistant to acids, bases and salts, assuring a lower maintenance cost and a longer performance life
Impact strength: Resistant to compression and impact, suitable to be buried in concrete
Easy Installation: solvent cement and threading joining
Usage:Electric wires installation, Supply water, Irragation Water, Drainage

Q: I am trying to design a tube that needs a lid which will have rubber seals. therefore i need to figure out what the series roughness should be on the tube where the rubber seals need to sort of slide in. the tube is about 12.5in long and will be smooth 1.5in in on the inside and the cover goes 1.5in into the tube when put on the tube. This is for work, i am just trying to finish my drawings for this product.: 63 u/in will be fine.

Q: How are plastic tubes filled with creams or gels?: Plastic tubes are typically filled with creams or gels using a process called tube filling. This involves the use of a machine that pneumatically or mechanically fills the tubes with the desired product. The tubes are first loaded onto the machine, and then the product is pumped into them through a nozzle. The machine ensures accurate and consistent filling by controlling the amount of product dispensed into each tube. Once filled, the tubes are sealed and can then be labeled and packaged for distribution.

Q: My house is two floors, though I think it was originally a one-story cape cod, and the upstairs was a single semi-second floor/attic. Anyways, the attic is now higher up, but the walls still slope on the sides. The air/heating unit is in the crawl space, duct work runs directly to vents/returns on the first floor, but for the second floor there are these two really large plastic(?) pipes that run up to the second floor from which I believe the ductwork is distributed. What are these called?: Vertical duct work. In general, if forced air, heated, cooled or even unconditioned, goes through it it is called duct work, unless it is an accessory / fitting such as a grille, diffuser, register etc. It's called duct work or vertical duct work if you would like.

Q: Glass surfaces are negatively charged, and when blood is collected in a clean glass test tube, it clots. Explain this observation.: it doesnt matter if it's glass or plastic. Once exposed to air (oxygen) the blood will clot unless it's been treated with an anticoagulant like EDTA, heparin, or sodium citrate. That's why these test tubes have anti coagulant in them. The tubes themselves can be glass or plastic, it doesn't matter. No anti-coagulant = clot anti-coagulant = no clot.

Q: I make models and the plastic that winds up in the trash could be reused if only I knew how to glue it. I have tried all of mine (401, epoxy, Loctite, Gorilla Glue, etc) to no avail.: I use E-6000 clear glue for almost everything. I am a sewer and needed some weights so I used this glue on huge metal washers putting two of them together for more weight. I have had these weights for quite a few years. The trick to this glue is to let is set. According to the label is it flexible, paintable, non-flammable, waterproof, safe for photographs, etc. I would suggest not using this in an enclosed area for any length of time. Good luck - Hope that helps.

Q: What is the best re-cycling method for plastic bottles & tubes?: there is an industry located in Sumter, SC named Clor-Fi that recycles plastic bottles, etc by melting them down and extruding the material into carpet yarn. The company has been here doing this for 20+ years.

Q: What are the common wall thicknesses for gas line plastic tubes?: The common wall thicknesses for gas line plastic tubes vary depending on the specific application and regulations. However, some common wall thicknesses for gas line plastic tubes range from 0.060 inches (1.5 mm) to 0.120 inches (3 mm).

Q: What are the types of plastic pipes?: Chlorinated polyvinyl chloride pipe is a new kind of water supply pipe made of chlorinated polyvinyl chloride resin. Its biggest advantage is that it is more resistant to high temperature. This pipe application in China just started in recent years, is used in cold water and waste water, chemical solution conveying pipeline, long-term use of infusion temperature up to 120 degrees Celsius, life for 40 years.

Q: I need to buy plastic (or clear colored) plastic tubes with caps. Approximately 5 or 6 inch in length and close to 1 inch or close to it in width. Would appreciate any suggestions where I find it.: the hardware giants like Lowe's and the Ho Depot are your best bet ... go in the store and ask for plastic tubing==== HEY !! you might do better to go to a friendly pharmacy and get some clear plastic medicine bottles ... go and ASK ... and if this is

Q: Why plastic tubes against UV radiation?: You can't resist UV if you don't add itFor example, if a pipe is buried in the ground, this function may not be needed

Send your message to us

*Email

*TEL

*Quantity

*Unit