PPR stop valve with brass from Top chinese factory

Ref Price:
Loading Port:
Tianjin
Payment Terms:
L/C,T/T
Min Order Qty:
2400 pc
Supply Capability:
230000 pc/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Product Features
1. Corrosion resistance
PPR pipes and fittings can resistant to most chemical corrosion; it can withstand PH value range 1-14 high concentration of acid and alkali corrosion over a wide temperature range.
2. Installation performance
PPR pipe PPR pipe is light in weight, and the operation installation is easy, which make it available to weld again. It is very important that pipe and pipe fittings can be welded together in seconds with a simple tool. Compared to traditional connection methods it can save 40%~50% of the time.
3. Safety Indicators
The basic component of PPR is carbon and hydrogen which is simple. It keeps in line with food hygiene regulations, non-toxic. If you use PPR pipe, there will no dirt in the inner wall or “secondary water pollution” caused by rust any more.PPR pipe ,green building materials, is more suitable for transporting drinking water.

Advantages of PPR pipe
1. Maximum operating temperature can up to 95℃; it can work in a long term under the condition of 70℃ and 1.0Mpa.
2. PPR pipe density is only 1/8 of metal pipe; pressure resistance strength test is up 5Mpa, with good toughness, impact resistance.
3. Inner diameter of PPR pipe is little bigger than that of pipe fittings, which can ensure not to increase the resistance to fluid flow.
4. Inner wall of PPR pipe is smooth, no rust, no scaling, small fluid resistance
5. PPR pipe has excellent insulation properties, can significantly reduce the vibration and noise caused by the flow of liquid.
6. PPR pipe energy consumption is only 20% of steel pipe; its thermal coefficient is also only 1/200 of steel pipe, reducing heat loss greatly.
7. PPR pipe is poor electrical conductor material, which can avoid galvanic corrosion phenomena.
8. With poor thermal conductivity, PPR pipe can reduce condensation.
9. PPR pipes, fittings are recyclable.
PPR stop valve with brass from Top chinese factory

Application
1. Hot and cold drinking water supply system of civil and industrial buildings
2. Clean, pure water piping system
3. Beverage production and transport systems
4. Industrial liquid delivery system
5. Central air conditioning system
6. Hot water circulation Heating System
7. Compressed air piping system
8. Garden and greenhouse irrigation systems

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:What are tube flies? Where can you get them?
Tube okorder.com in a few weeks. You will find many proven options for many situations. If you want to buy some as a first time tube fly fisher then you will be in good hands. We also have a wonderful tube fly box out. The Tribute tube fly box is new for the 2009-2010 season. You will find this box will hold a bunch of tube flies and you can push heavy cone heads in snug. If you are looking for a gift, this would be great for any fly fisherman. You can also contact Clarke at Puget Sound Fly Company. Besides being a great soccer coach he is well schooled in tube flies. His shop will have some great patterns for you until I am finished the first tubes for the public. Puget Sound Fly Company is one that Irideus tips its hat at for the many long hours testing put in over the years. Good luck, we are all happy to help you get going. Tim Owner Irideus
Q:Where is the a/c evaporator condensation drain tube on a 1998 Dodge Stratus? What's the best way to clean it
The drain will be on the passenger side, towards the bottom of the firewall. It should be below the 2 heater hoses that go intot he heater core. On yours, I think it was just a tube coming out of the firewall, it will have a foam gasket around the platic tube. The tube will protrude from the firewall just a little bit. Some have a 90 degree rubber elbow on the end of the tube. If it is just the plastic tube, without the elbow, then use either a wet/dry vac if you have one, or use a wire hanger to poke into the hole and try to remove whatever is blocking the drain. If you don't get it out, it might block it again later, or it might come out with the water. If you have the 90 degree rubber elbow, a quick trick is to squeeze it at the very end and roll it between your fingers to loosen the blockage. If that doesn't work, remove the elbow and clean it out, it will generally have the blockage in it. The elbow should have 2 pieces of wire sticking out, just squeeze these together and slide it off. Might have to give it a twist to get it to come loose. If you get the elbow off and water doesn't come rushing out, then clear the plastic tube, and check the elbow to be sure it isn't clogged.
Q:How to get water to drain from a pitcher with a tube?
By blowing do you mean no sucking? If you can suck the water to start the siphoning. try moving the tube up and down fast enough in the water to start the siphoning action. The other way is to secure the top so nothing dumps out and turn it upside down. The tube will be on the bottom and gravity will suck it out of the pitcher.
Q:i have a top fin 30 filter,and i was wondering should bubbles be coming out of the clear plastic tube?
You might have some air in the line, you might also have water with a high dissolved gas count and it's coming out at the tube. As long as it's pumping water well, I wouldn't worry. If the flow seems inadequate you might want to consider calling the manufacturer and seeing if it's something that is set up wrong and they can help you correct, of if it needs to be replaced (hopefully under warranty).
Q:How do I clean a plastic tube of diesel fuel?
Yea right, so you ask it in the You Tube section,........ lol good try but a troll question.
Q:What can you use for a mortar firework tube?
Fiberglass Mortar Tubes
Q:what are those 5-6ft light stand up tubes filled with water with a bubble and light affect?
I know just what you're talking about, in fact I used to have one. I figured you could find them just doing a google search, but no, there doesn't appear to be anything out there. I suspect the company went out of business.
Q:How do you put the plastic pick up tube on to the brass pick up tube on a briggs and straton carburetor?
Put a little oil and push and twist
Q:where can I find tubing? aluminum or like a clear pvc?
Online and they have everything.
Q:Reinforced concrete walls are eyes, and some have plastic tubes on their eyes, what's the matter?
It will produce pressure on the template, the higher floors, the greater the pressure, so the template is needs to be strengthened, with steel reinforcement wall, the middle of the plastic pipe is used to wear on the screw pull, to pull the screw will be fixed on both sides of the wall fixed template, the template system in concrete is very stable the.

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range