Pneumatic Can Seaming Machine for Tin Cans

Ref Price:

Loading Port:: China Main Port

Payment Terms:: TT or LC

Min Order Qty:: 1 Set set

Supply Capability:: 1000 Sets per Month set/month

Inquire Now

Add to My Favorites

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

You Might Also Like

Metal Guillotine Manufacturer XR-40

Sheet Plate Guillotine Shear Machine

Square Paint Can Seaming Machine

Tin Can Body Welding Machine

Pneumatic Tin Can Welding Equipment

Tinplate Slitting Machine

Tinplate Metal Cutting Machinery

NEW DODO-600 Fully automatic can body welder

pneumatic can seaming machine

1,to seal/close 1-24L tin cans.

2.15-20pcs/min

3.diameter: 50-330mm

4.easy operatation

Main technical parameter:

Applying range

50-330mm

Production capacity

Square-shaped can:12-15/min

Round-shaped can:15-20/min

Electromotor

Type: Y100L-6-V1

Power: 2.2KW

Rotating speed: 940/min

Size

1500×800×1800mm

Weight

About 700kgs

Main application:

This can sealing machine is one of necessary equipments in round or square can making production line. it is sealing machine/seamer among the production line. It is used to seal/close can lid and can bottom/end at can body tightly, and without leakage. if customers want to seal other size of cans, just need to change the sealing/seamer mould.

Q: What is the welding time of welded cylindrical battery in resistance spot welding machine?: Look at the power of your equipment. It's almost the same in 3-5 cycles.

Q: What is the output current of 75KVA spot welder?: Should be adjustable

Q: Spot welding temperature is too high to deal with: Do you use pedals?

Q: When the spot welder is in use, the voltage of the line will be higher and lower. What can be done to solve it?: The single-phase AC spot welder should be used. The single-phase power supply of AC spot welder has destroyed the balance of power grid and seriously affected the normal operation of other power equipment. The inverter type spot welder is supplied by three-phase power supply, and its operation does not affect the three-phase balance of the power grid.The power factor of welding machine is an important index that affects the utilization ratio of power supply equipment. If the power factor of welding machine is doubled, the requirement of power supply capacity will be reduced by 1/2. Because the resistance welding machine outputs is the low voltage, the big current. Therefore, the inductance of the secondary circuit of the welding machine is obvious, so that the power factor of the AC resistance welder can only reach 0.3~0.5. The inverter type resistance welding machine outputs DC welding current, and the power factor of welding machine can be as high as 0.95. Therefore, the requirement of the power supply capacity of inverter type resistance welding machine is less than that of the AC welding machine of the same capacity as 1/2.

Q: With high-capacity capacitor charging and discharging, can you do a spot welder, how to do, please point out /?: The voltage is not too high, below 30V is suitable to use capacitor discharging current, small resistance varieties, Japan has a large current discharge capacitor special, electrolytic capacitor cannot generally be used, easy to lead to interrupt, if found, with multiple capacitor array, parallel capacitor, in addition to the pressure circuit the design for charging the capacitor to adjust the capacitance energy storage size, with different thickness of the workpiece, condenser type spot welder I only met with little dental stainless steel wire, the discharge current is only 0.5 below the welding wire, the specific capacitance of the capacitor, but also forget is not expensive, can use different capacity, different voltage to test a few times, small capacity low voltage to gradually experiment, how have the general voltage from several thousands of micro method, V. From the capacitor to the spot contact line should be thick enough, dental point fine wire, is to use one centimeter in diameter of the brass rod, transformer spot welder I did also, with the brass tube diameter of 6 cm, inside water, little chicken cage with..

Q: Is the foot welding machine good with or without time relay?: In fact, almostThe time relay is also very low in price

Q: What harm does the factory spot welder work to people?: Basically no harm, rest assured to use.

Q: AC spot welding of two different materials (0.25 thick stainless steel and galvanized steel plate with 0.6 mm thick) is taking off, how to solve?: EWM cold arc welding may be considered

Q: Why don't we use the welding spot welder professional welding galvanizing plate is copper!!: The port spot welding of high precision, can be welded thin plate, galvanized plate can adopt 2 welding, namely a power failure zinc layer, two discharge welding, spot welding machine can assist you in the ginger port and a discharge of traditional spot welding into 2 discharge spot welding.

Q: Mine is DNJ-25 mobile time control spot welder. The cooling water circulation is too slow. The pipe will be hot after welding for a while. The pipe is hot and cracked once. How can the cooling water circulate and flow faster? Seek expert advice. I am a bucket on the top, a barrel down the next.: Welding current I Omega heat is proportional to the square of the current, so the welding current is most sensitive to the solder joint performance. When keeping other parameters unchanged, when the current is less than a certain value of nugget is not formed, more than this value, the nugget increases rapidly with increasing current, joint strength increased, and then due to increased heat and nugget growth slowed down, the shear strength increases slowly, such as to further improve the current leads to splash, solder joint strength decreased. Therefore, it is generally recommended to use the neutral current (BC segment) insensitive to the nugget diameter to weldThe welding time, t, the duration of the ohmic charge directly affect the input heat. At the current widely used control spot welding machine, the power on time is the integer multiples of the cycle. In the case of other parameters fixed, only when the discharge time exceeds a minimum value, the nugget will begin to appear, and then with the increase of the power up time, the nugget will increase rapidly first, and the tensile shear force will also increase. When the selected current is moderate, the power up time is further increased, and the nugget growth slows down and becomes constant. But because the heating time is too long, the organization is poor, pull down, the plasticity index (ductility ratio: F /F) decreased.

In area of technic, research and development, We have a batch of professional and technical personnel in product development and manufacture and production management, some of our products have applied patent, so we believe our high technology and high quality products can meet the updating requirements of customers. We always keep "good business by sincerity and honesty, client's profit in first position" as our management principle. And we have been appraised as a corporation that "pay importance on contract, and keep sincerity" by local government for many times.

1. Manufacturer Overview

Location	Jiangxi,China (Mainland)
Year Established	2010
Annual Output Value	Below US$1 Million
Main Markets	South America 1.04 Southeast Asia 3.26 Africa 7.92 Mid East 8.81 Eastern Asia 0.54 South Asia 2.25 Domestic Market 76.18
Company Certifications	Consumer Trustworthy Company;Member of Chiese packaging technology association;Trust-worthy Company

2. Manufacturer Certificates

a) Certification Name
Range
Reference
Validity Period

3. Manufacturer Capability

a) Trade Capacity
Nearest Port
Export Percentage	41% - 50%
No.of Employees in Trade Department
Language Spoken:	English, Chinese
b) Factory Information
Factory Size:	5,000-10,000 square meters
No. of Production Lines	6
Contract Manufacturing	OEM Service Offered Design Service Offered
Product Price Range	Average