Monocrystalline Solar Panels-Tire 1 Manufacturer-190W

Ref Price:
Loading Port:
Payment Terms:
Min Order Qty:
10000 pc
Supply Capability:
50000000 pc/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Product Description:

Solar Monocrystalline Series Panels

Introduction of Monocrystalline Solar Panels

CNBM Solar photovoltaic (PV) Panel is designed for large electrical power requirements. It is the optimal choice for both on-grid and off-grid power systems. CNBM Solar panel offers high performance of power per square foot of solar array. Monocrystalline silicon(c-Si): often made using the Czochralski process. Single-crystal wafer cells tend to be expensive, and because they are cut from cylindrical ingots, do not completely cover a square solar cell module without a substantial waste of refined silicon. Hence most c-Si panels have uncovered gaps at the four corners of the cells.


Characteristics of Monocrystalline Solar Panels

I Solar Cell : High efficiency crystalline solar cell. Even if under the weak light, the solar module can produce maximum power output.

II Tempered glass (toughened glass): Anti-reflecting coating and high transmission rate glass increase the power output and mechanical strength of solar module.

III EVA and TPT: Using high quality EVA and TPT to prevent destroying and water.

IV AI frame: Without screw, corner connection. 6 holes on the frame can be installed easily.

V Junction box: Multi function junction box with water proof.

VI Long lifetime: ≥25 years; Less power decrease

VII Good performance of preventing from atrocious weather such as wind and hails.

VIII Resisting moisture and etching effectively, not effected by geology.


Standard Test Conditions of Monocrystalline Solar Panels

The opto-electrical specifications shown below are stabilized values being measured at Standard Test Conditions, Irradiance: 1000W/m2, Spectrum: AM1.5 at 25°C, The info below is subject to manufacturing tolerances. Where appropriate minutes of measurement are available and are used for the dimensioning of the installation.


Advantages of Monocrystalline Solar Panels

• CNBM Solar performance guarantees for 25 years

• 12 years guarantee for workmanship

• Timeliness of delivery

CNBM International Corporation's products including Monocrystalline Solar Panel, Polycrystalline Solar Panel have received and enjoyed famous reputation in many countries and regions in the world .As a solar panel supplier in China, we strive to provide our customers with excellent service, superior products and unmatched value.


Characteristics of Monocrystalline Solar Panels


Max Power Voltage Vmp (V)



Max Power Current Imp (A)



Open Circuit Voltage Voc (V)



Short Circuit Current Isc (A)



Max Power Pm (W)



Temperature Coefficient of Cells



Temperature Coefficients of Isc (%/)


Temperature Coefficients of Voc (%/)


Temperature Coefficients of Pmp (%/)


Mechanical Data Solar Monocrystalline Series









The dimension of the modules can be changed according to the demand of clients


Operating Temperature

–40 °C to +85°C

Storage Temperature

–40 °C to +85°C

Max System Voltage


Guarantee Solar Monocrystalline Series Panels

Products Guarantee

10 yrs free from defects in materials and workmanship

Performance Guarantee

No less than 90% within 10yrs and no less than 80% within 25yrs




Examination of Solar Monocrystalline Series Panels



Monocrystalline Solar Panels-Tire 1 Manufacturer-190W


Monocrystalline Solar Panels-Tire 1 Manufacturer-190W


Monocrystalline Solar Panels-Tire 1 Manufacturer-190W





We have organized several common questions for our clientsmay help you sincerely


1.    What’s price per watt?

A: It’s depends on the quantity, delivery date and payment terms of the order. We can talk further about the detail price issue. Our products is high quality with lower price level.


2.    Can you tell me the parameter of your solar panels?

We have different series of cells with different power output, both from c-si to a-si. Please take our specification sheet for your reference.


3.    How do you pack your products?

We have rich experience on how to pack the panels to make sure the safety on shipment when it arrives at the destination.


4.    Can you do OEM for us?

Yes, we can.


5.    How long can we receive the product after purchase?

In the purchase of product within three working days, We will arrange the factory delivery as soon as possible. The perfect time of receiving is related to the state and position of customers. Commonly 7 to 10 working days can be served.


Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:Will a 2W, 2V mono solar panel power up a laptop battery?
I'm afraid neither of these panels will do much for charging or running your laptop. If the power brick is supposed to emit 5 volts at 5 amps, that's 75 watts. Neither of those panels provides enough voltage and the power output is obviously far too small. The capabilities of solar power are vastly overestimated for small panels. Sunlight is limited to about kilowatt per square meter under ideal conditions (summer time, clear blue sky, for a few hours around noon in the US southwest). But consumer panels top out at about 5% efficiency, so your limit is 50 watts per square meter - in other words you would need about half a square meter, or about six square feet, of panel to provide 75 watts. And even under ideal conditions you will only get that much for a few hours each day. Also, the panel's voltage output is not regulated, so even if you find a panel that emits 5 volts (this would actually have to be made up of groups of 30 cells in series, as they emit half a volt each at most) you can't just connect the panel output into your laptop's DC in. You'd need a regulated DC-to-DC supply, and since that is not 00% efficient it will cost a bit of the power... now you need even more panel area. All in all, not really a practical thing to carry along on a camping trip.
Q:Solar Panels in the 200 Toyota Prius?
Toyota Prius Solar Roof
Q:Anybody install solar panels themselves?
If you're in San Francisco, then the price of labor is going to be high. It's still legal to install your own, but you'll need to pull a permit, and get an inspection. If you hunt around on the PGE website, they'll guide you as to requirements. Aside from a standing-seam metal roof, the easiest install would be over asphalt shingle. As with any roof penetration, flashing and sealing the holes is critical.
Q:Solar Panels for Jacuzzi?
You can do this by isolating the jacuzzi, you will need a solar array adequate for the power draw of the jacuzzi, a charge controller, battery bank, off-grid inverter and switch gear. This is the expensive way to go--especially if you are planning to heat the water with the solar. A better option would be to heat the jacuzzi with solar thermal panels. It is plumbing instead of electrical, but the cost would be much less. If you still want to do PV (electric) solar, think about putting a non-isolated grid-tie solar array on your home. They are much cheaper, and if you think about it, it really does not matter if you use the solar electricity to run a light, a fridge, a TV, or a Jacuzzi, that amount of power is subtracted from your overall house power bill. Just size the array for the power output of the jacuzzi, and let the power meter do the rest. Your overall result will be the same and the system will be half the price, or less.
Q:I want to Build a solar Panel.?
Q:how to make your own solar panels ?
If . Beware of anyone who makes claims you can save tons of money by making your own panels. Those are scams. It's possible to save money with solar, but not with homemade panels.
Q:Good Idea To Install A Solar Power Energy On A Restaurant?
To begin with, you need to know how much power you need and then decide from there just how much you can or will have to pay to get that money back. Find a couple companies that do this kind of work to give you some figures to work with
Q:How many LED's can power a solar panel?
Q:Designing 3d Solar Panels?
I don't know anything about the 3D thing. You cannot get more energy out, than goes in. Energy will only hit the mirrors. With some loss of efficiency they would reflect a focused beam into the chamber, where with some more losses would reflect it to the solar panels. It would be more efficient just to expose all the panels to sunlight.
Q:Solar panel connectionI
The answer is that the two panels should be put in parallel. The voltage out will drop to the voltage of the lower panel, but you should get most of the power, if the panels aren't too badly mismatched. I would try to get a multimeter and try to measure the actual current coming out of the panels in full sun. Sometimes the specifications on these smaller panels are very optimistic. If the whole setup is putting out less than 2 amps, I'd say wire the whole thing straight to the battery - little chance of boiling the electrolyte at those currents.

1. Manufacturer Overview

Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range