Q:Water heater hose 4 points and 6 points difference

4, in charge of 1/2 inches of pipe, 6 in charge of 3/4 inches of pipe, different specifications of some differences.The so-called 5 turn 4, should be different diameter, that is, pipe and pipe joints, parts of different specifications.A bellows is a pipe, not flat, corrugated.

Q:How can I remove all the flavor on the rubber hose?

The rubber itself is tasteless, and the smell of the rubber we smell is the flavor of a vulcanizing agent or accelerant.Cover or dry.

Q:What are the categories of hose?

According to the use of performance: ordinary hose (cloth water hose, air hose, braided hose, air hose braided fiber, fiber winding hose, fiber winding air hose (hose); medium resistance oil resistance, acid and alkali resistant hose, steam hose etc.); special hose (hydraulic hose, brake hose drilling mud, hose, spray hose, hose extrusion etc.) Hengshui Yajie rubber.

Q:What is the principle of communicating devices? What if the rubber tube is used as a connecting device to change the water for the fish?

The principle of communicating devices can be explained by liquid pressure. If the same liquid is contained in a U glass tube, a small liquid AB is conceived at the center of the bottom of the communicating device. If the liquid is stationary, it does not flow. The pressure of the liquid in the left tube toward the right side of the liquid AB must be equal to the pressure of the liquid in the right tube toward the left of the liquid AB. Because in the communicating vessel is filled with a liquid, the same two liquid column density, according to the formula of P= P GH liquid pressure that only when both sides is equal to the height of liquid column, the liquid column is equal to the pressure on both sides of the liquid film AB. Therefore, in the case of no flow of liquid, the liquid level in each vessel of the communicating device shall be kept flat. (ideal model method) the connecting device is characterized in that the liquid level in each container is flat only when the same liquid is contained in the container. If the container is tilted, the liquid in each container is about to begin to flow. One end of the liquid column flows to the lower end of the liquid column and stops flowing until the liquid level in each container is normal. As with rubber tube two glass tubes connected together in container with a liquid, which will be a fixed tube, the other tube up and down or tilt, can see the two tube level in stationary phase remained flat. The connecting device is provided with the same liquid, but the pressure on the liquid surface is unequal, and the pressure difference of the liquid surface is equal to the pressure difference produced by the liquid level difference of the two container of the communicating device.

Q:Toilet hose and water tank joints leaking, how to repair?

Remove the joint, wrap the tape, and press again

Q:Stainless steel metal hose and flexible rubber joint which is easy to use?

The pressure and temperature bearing capacity of the stainless steel metal hose shall be due to the rubber joint, and the length of the product can be customized according to the requirements of the field, and the form of the joint is very rich.

Q:What is negative pressure rubber shock proof joint? Is vacuum piping available?

With high pressure, good elasticity, large displacement, balance pipe deviation, absorbing vibration and noise reduction effect, convenient installation, but also can greatly reduce the noise and vibration of the pipeline system, which can solve all kinds of line interface displacement fundamentally, axial expansion and concentricity problems, mainly installed in the pump inlet the vacuum pump inlet, or large, can solve the 100% rubber joint suction flat phenomenon.

Q:The difference between hose and rubber tube

Silicone tube: also known as silicone tube. Used as liquid, gas, and other materials to circulate and coat carriers.Latex tube: latex tube is made of latex material of different thickness of tubes, mainly used in hospitals, equipment factories, power plants, research laboratories and other fields, but also related to bungee jumping, trampoline and other places of entertainment.

Q:How about rubber transfusion hose?

The use of calender will glue paddle pressed into the middle, and then add the separant winding and made in accordance with the provisions of the production process requirements of winding hose cutting width.

Q:How to identify the quality of rubber pipes for sewage treatment?

The general hose inside and outside the adhesive layer material with natural rubber, styrene butadiene rubber or butadiene rubber; hose with chloroprene rubber, nitrile rubber; acid and alkali resistant, high temperature resistant hose with ethylene propylene rubber, fluorine rubber or silicone rubber etc.. Structure: hose structure is usually divided into inner layer, outer layer and skeleton layer (or middle layer). The inner layer directly bears the abrasion and erosion of the conveying medium; the outer rubber layer protects the inner part of the hose from the damage and erosion of the external environment; the stock price is the pressure bearing layer of the rubber tube, and gives the strength and rigidity of the tube body. The working pressure of the hose depends on the material and structure of the skeleton.