GT350E BQ.TADANO MOBILE BY TADANO TECHNOLOGY JAPAN
- Loading Port:
- Tianjin
- Payment Terms:
- TT or LC
- Min Order Qty:
- 1 unit
- Supply Capability:
- 10 unit/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
MASS
Gross Vehicle Mass: 34400 kg
Front axle mass: 12205 kg
Rear axle mass: 22195 kg
PERFORMANCE
Max. traveling speed: 74km/h
Gradeability(tanθ): 46%
Min. Turning radius: 11000 mm
Minimum Ground Clearance: 320mm
1.UPERSTRUCTURESPECIFICATIONS
BOOM
4-section full power partially synchronized telescoping boom of hexagonal box construction with 5 sheaves at boom head. The synchronization system consists of 2 telescope cylinders, extension cables and retraction cables. Hydraulic cylinders fitted with holding valves.
Fully retracted length -----10.6 m
Fully extended length ------ 34 m
Extension speed ----- 23.4 m in 127s
JIB
2-staged boom extension type. Triple offset(5º/25º/45º)type. Stored under base boom section. Single sheave at jib head.
Length --- 8.8 m, 15.2m
SINGLE TOP
Mounted to main boom head for single line work.
ELEVATION
By a double-acting hydraulic cylinder, fitted with holding valve.
Automatic Speed Reduction and Soft Stop function.
Elevation speed -----2º-80ºin /62s
HOIST--Main winch
Variable speed type with grooved drum driven by hydraulic axial piston motor through winch speed reducer. Power load lowering and hoisting. Equipped with automatic, brake (Neutral brake) and counterbalance valve. Controlled independently of auxiliary winch.
Single line pull -----31.2kN(3,190 kg)
Single .line speed ----118m/min (at the 4th layer)
Diameter-----16mm '
Length-----.190m
HOIST-Auxiliary winch
Variable speed type with grooved drum driven by hydraulic axial piston motor through winch speed reducer. Power load lowering and hoisting. Equipped with automatic brake and counterbalance valve. Controlled independently of main winch.
Single line pull -----34.3 kN ( 3,500kg )
Single line speed -----102 m/min (at the 2nd layer)
Diameter. -----16 mm
Length-----110 m
SWING
Hydraulic axial piston motor driven through planetary speed reducer. Continuous 360~ full circle swing on ball bearing slew ring. Automatic Speed reduction and soft stop function. Equipped with manually locked/released swing brake.
Swing speed -----2.5r /min
HYDRAULIC SYSTEM
Pumps-----Quadruple gear pumps driven by carrier engine through P.T.O.
Control valves-----Multiple valves actuated by pilot pressure with integral pressure relief valves.
Circuit------Equipped with air cooled type oil cooler. Oil pressure appears on AML display for main circuit.
Oil tank capacity-----approx. 527liters
Filters ------Return line filter
CAB AND CONTROLS
By 4 control levers for swing, boom hoist, main winch, boom telescoping or auxiliary winch with 2 control pedals for boom hoist, boom telescoping based on ISO standard layout. Control lever stands can change neutral positions and tilt for easy access to cab.
Steel construction with sliding door access and tinted safety glass windows opening at side, and operator's 5 way adjustable seat with headrest and armrest.
OUTRIGGER
4-hydraulically operated H-type outriggers. Each outrigger controlled simultaneously or independently from either side of carrier. Equipped with sight level gauge. Floats mounted integrally with the jacks retract to within vehicle width. All cylinders fitted with pilot check valves.
Crane operation with different extended length of each outrigger.
Equipped with extension width detector for each outrigger.
Extended width
Fully-----6,100 mm
Middle-----4, 000mm
Float size (Diameter) -----400 mm
TADANO Automatic Moment Limiter
Main unit in crane cab gives audible and visual warning of approach to overload. Automatically cuts out crane motions before overload. With working range (load radius and / or boom angle and / or tip height and / or swing range) limit function.
Nine functions are constantly displayed.
Either moment as percentage or main hydraulic pressure
Either boom angle or moment %
Either boom length or potential hook height
Either actual load radius or swing angle
Actual hook load
Permissible load
Either jib offset angle or number of parts of line of robe
Boom position indicator
Outrigger position indicator
FRONT JACK
Front outrigger mounted to the front frame of carrier to permit 360ºlifting capabilities.
Hydraulic cylinder fitted with pilot check valve. Equipped with front jack extension detector.
Float size (Diameter) -----260 mm
COUNTERWEIGHT
Integral with swing frame
Mass-----4100 kg
DEMENSION
Overall length-----12,770mm
Overall width-----2,490mm
Overall height-----3,570mm
- Q:What is the principle and purpose of the rotary joint of the truck crane center?
- Is the rapid flow of water through the propeller will be converted into mechanical energy to promote its high-speed operation of the generator power generation
- Q:What are the specifications and standards for truck cranes and tire cranes?
- Safety technical conditions for motor vehicle operation GB 7258
- Q:What is the development trend of truck cranes in China?
- Larger tonnage of new products to meet the needs of the market. The only way to get nutrients and vitality from the market to survive, survive in development, grow in development
- Q:Does the truck crane commander need a document?
- Yes, commanders and operators need to be certified.
- Q:Is the truck crane a special equipment?
- Crane boom transmission structure is complex, mechanical or hydraulic system in the event of a problem, will lead to greater risk, lead to accidents, involving life and property security, so it needs to be classified as special equipment for management.
- Q:What operating permits are required for truck cranes?
- The driver of a car crane must obtain a special motor vehicle driver's license issued by the public security traffic management department;
- Q:What are the types of truck cranes?
- Due to the use of requirements, its weight has increased the trend, such as has produced 50-1200 tons of large car cranes.
- Q:What is the hook crane technique?
- Stop hook, slow,Shake hook, to coincide with the turntable speed.
- Q:What are the safety measures for car cranes to eliminate hidden dangers?
- The reverse oil path of the hydraulic check valve is only connected when it controls the oil input to a certain pressure oil
- Q:What is the reason for the jitter of the crane boom
- Exclusion method: the balance valve disintegration cleaning, dredge damping holes.
1. Manufacturer Overview |
|
---|---|
Location | |
Year Established | |
Annual Output Value | |
Main Markets | |
Company Certifications |
2. Manufacturer Certificates |
|
---|---|
a) Certification Name | |
Range | |
Reference | |
Validity Period |
3. Manufacturer Capability |
|
---|---|
a)Trade Capacity | |
Nearest Port | |
Export Percentage | |
No.of Employees in Trade Department | |
Language Spoken: | |
b)Factory Information | |
Factory Size: | |
No. of Production Lines | |
Contract Manufacturing | |
Product Price Range |
Send your message to us
GT350E BQ.TADANO MOBILE BY TADANO TECHNOLOGY JAPAN
- Loading Port:
- Tianjin
- Payment Terms:
- TT or LC
- Min Order Qty:
- 1 unit
- Supply Capability:
- 10 unit/month
OKorder Service Pledge
OKorder Financial Service
Similar products
New products
Hot products
Related keywords