Q:Physical short answer, put an object on the conveyor belt why the first to accelerate after the uniform speed

Because the moment just put the speed is no speed, and between the conveyor belt and the friction between the object, then the transmission with the object to do even acceleration movement. When the conveyor belt is long enough, after a certain period of time the same speed as the conveyor belt, it becomes uniform....

Q:What is the motor used in the pipeline in the factory? Above also equipped with a reducer, you can adjust the speed of the motor, this motor is what motor? What is the general model? How can we buy the right motor? I do not know what type of motor to buy ////////////////////////////////// more

Generally speed motor, frequency control

Q:The motor has a fixed diameter wheel, connecting the conveyor belt. Conveyor belt with a large round of walking slow, or with a little bit of the wheel to go slow?

The larger the wheel on the conveyor belt, the slower it is. Because the wheel on the motor shaft is longer than the long wheel circumference on the conveyor belt, the longer the wheel on the conveyor belt, the longer the circumference of the wheel, the wheels on the motor shaft to turn a few laps, the big wheel may not turn The

Q:How to determine the direction of friction in the conveyor belt problem? For example, an object from the oblique conveyor belt down, the belt clockwise movement, then what direction of friction, how to judge? The same circumstances, if it is counter-clockwise movement, what is the direction of friction? Seek advice! More

And the opposite direction of movement.

Q:To design a conveyor belt, 2 m / min, 3 m long, used to send the PCB board, very light, that is, do not know the choice of the motor, what about the power, and the wheel is not casually size, , The motor to add the inverter, or gear motor, or electronic regulator? Which is more suitable, why? Can you tell me Do not copy some online have to perfunctory! Thank you! More

There are ready to set, why trouble.

Q:I have two sets of conveyor belt, cylinder and air compressor, the trachea are connected. The existing JS14P time relay 1, CJX2-1210 contactor 2, are AC220V, diffuse photoelectric switch 1 [2 lines often open 220V], how to wiring? Puzzled line of their own, but there is a contactor will be baffled, how to solve, how to properly wiring. Urgent thanks! Question added: I would like to ask which master can draw a picture really thank the younger brother

It depends on the size of the object you deliver, the line speed. Time relay to add a self-locking circuit.

Q:The factory made a 2-meter-long small conveyor belt, do not know what kind of motor and control? The motor starts to stop frequently, the minimum 1 second time, with a signal to control the conveyor belt to stop, and stop when the request to stop immediately, are not allowed to inertia. More

DC

Q:Is the design of a conveyor belt, do not know the motor on the conveyor belt to choose how much power, who can give more detailed answer

Motor and reducer are provided by the state

Q:If there is a conveyor belt, use a smaller force to push the gear so that the other side of the larger force of the gear rotation

Hello, you describe the process it is a deceleration principle, with the drive that is called the pulley or called the drive wheel or driven wheel is not a gear, as shown in Figure: You mean that the small pulley turns when the big pulley turns, At this time set the drive wheel, as long as the drive wheel (small) installed motor drive motor drive can drive a large pulley. Leave you can explain in detail to help you.

Q:My automatic mahjong table conveyor belt how to reverse the motor, it should be up to send the card, and now it will pass down the card, resulting in the card simply do not get on, the magnetic circles suck the cards are gone, Do not say anything more

Have you ever been repaired? According to what you said, I made a look at the analysis, please refer to: First, as the first floor said, continued electrical (capacitor) is broken, you can change a high-power, but the motor will have some sound, can barely use. Or directly replace the motor Second, the conveyor belt dirty, mahjong table conveyor belt motor with a reverse function, if the belt is dirty, forward belt does not move, it leads to reverse. You can spray Billy beads on top of the belt to try, it is best to wash mahjong. Third, the motherboard is broken, it is more complex, motherboard circuit problems, according to the brand you buy, find manufacturers to replace the general warranty. Fourth, K4 light sensor for, resulting in not read the card, paint about the light, that is, on the licensing device, there are two small bulb-style stuff. You can also adjust its sensitivity to try. Fifth, the mahjong table this stuff, fear of tide, pay attention to keep dry. Sixth, if the above method no longer, mahjong table with automatic detection file, you can adjust to the detection file, automatic detection, according to the instructions. If not, it is best to find a professional. This is my personal point of maintenance experience, hoping to help you. for reference only.