Flame-resistant Power Cable YJV

Ref Price:
Loading Port:
China Main Port
Payment Terms:
TT or LC
Min Order Qty:
-
Supply Capability:
-

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

 

1. Flame-resistant Power cables' standard

GB/T12706.1-2008 " Rated and below voltage 35KV copper and aluminum  plastic insulated power cable";

2. Using characteristics

a.The cable conductor's long term working temperature can't be more than 70 DEG c.

b.The cable conductor's temperature can't be more than 160 DEG c when it was short circut (the longest keeping time can't be more than 5 seconds).

3.Application

The cable is suitable for supply, distribution and underground rated voltage 0.6/1KV. For laying indoors, in tunnel, cable trench and a pipe, cable unable to bear external mechanical force, cable laid underground  be able to bear external mechanical force, but can't  under external pressure.

4.Flame-resistant Cable's model and specification

Name

Type

Area(mm2)

Cores

PVC insulated and coated copper flame-resistant power cable

ZR-YJV

1.5,2.5,4,6,10,16,25,35,50,70,
95,120,150,185,240,300,400

1

PVC insulated and coated copper flame-resistant power cable

ZR-YJV

1.5,2.5,4,6,10,16,25,35,50,
70,95,120,150

2

PVC insulated and coated copper flame-resistant power cable

ZR-YJV

1.5,2.5,4,6,10,16,25,35,
50,70,95,120,150,185,240

3,4,5

Pictures

 

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:Question about threading a coaxial cable through brick?
A drill with a concrete bit (large enough to pass the wire, but smaller than the grout line(( cement between the bricks)). Try to determin where the studs in the wall are from the inside of the room and transfer to the outside. Drill a hole in the grout, then change the concrete bit for a long wood spade bit of the same size and drill a hole straight threw the wall. Leave the drill bit in the wall and attatch a small wire to the bit point with tape and pull back to the outside. Then put the cable onto the wire with tape as befor and pull threw the wall. Install a remodlers electric box and cover plate. Hope this helps Mike
Q:What cables do I need for this graphics card?
You don't need any power cables. The board gets power from the mother board. You need a PCI-Express slot on your mother board. If you're asking about video cables to the monitor, it says in the listing... Interfaces 2 x DVI-I - 29 pin combined DVI , 1 x HDMI - 19 pin HDMI Type A , 2 x DisplayPort - Apple mini-DisplayPort You only need one of these unless you are running more than 1 monitor. I would look on your monitor and see what connections you have. (2) DVI-1 is common is older stuff, (1) HDMI is the newest technology and common for HDTV, (2) Apple ports for Apple enabled monitors.
Q:xbox 360 power cable?
It depends on what chip set they have. An older Elite 360's power cable (with the older set) will fit into a new one, but not the other way around. It sounds like the one you just bought is older than the one that was banned.
Q:I want to put a switch in a power cable heading to USB Hub?
Before you attempt this, make sure you have the following items: -Wire strippers -Electrical tape -Two terminal switch -Scissors IMPORTANT! make sure that the cable is unplugged from the computer and the hub before you do this! 1st, cut the cord halfway with the scissors. Next, remove the outer wire insulation from the two new ends you just cut with the wire strippers. Now strip the small colored wires that are now exposed. Then connect the red wire from one half of the cord to a terminal on the switch. Do the same with the other red wire from the other half of the cord and connect it to the other terminal on the switch. Strip the other small wires and connect them back to their appropriate colored wire. Finally, wrap each wire individually with electrical tape, then wrap the entire gap in the cord with it. Now plug the cord in and try it out!
Q:What is this laptop power cable component called?
hi goto any pc store like pc world and buy one its a really difficult job just replacing the tip ok
Q:Can I plug the vehicle power cable directly into my Garmin Nuvi 370 device and not go thru the...?
Garmin makes a couple of power cords that go from one GPS to the other. Read the instruction manual, if it says a power cord plugs in there it will work. It will not recharge unless you have Ni-Cad rechargable batteries. Garmin is an excellent unit and you can moved saved info from other Garmins on your computer to your new one usually.
Q:power cable wiring question?
i would use 4ga. wire at the battery with a 120 curcuit breaker about 12-18 inches from the batery then 6-8 gauge off the dist.box to the amps
Q:What does the cable (YJV-5 * 6) mean?
Full name: cable ZR-YJV22-4 * 16MM2ZR: flame retardant ----- YJV22: copper conductor cross-linked polyethylene insulated PVC sheathed double steel belt wrapped armored power cable --- 4 * 16MM2: 4 core, each core 16 square millimeters.
Q:where can i get modular power supply cables?
I've never personally ordered any item specific parts but you should try NCIX . com
Q:Which power cable kit with new high output alternator?
I would go with the 1 ga wire. The fuse keeps the wire from setting your car on fire. The size of the alternator does not matter. The battery should supply 700 amps or so.

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range