Q:In unsaturated resins, what do solids refer to?

acid valueIs that the extent of reaction resin acid value index. The acid value is defined as the number of milligrams of KOH required with 1g resin, the acid value in mgKOH/g. Generally speaking, the smaller the reaction of high acid resin, resin acid and its formula but a great relationship, eventually stuffed formula values of different resins different.

Q:Hi there. The smoke detectors in my house have been randomly going off for the last couple of weeks. They will alternate between one or two beeps or go off for long stretches (5+ minutes). They are hard wired into my house. So when one goes off they all do. I have shut them off at the main breaker and changed the batteries and they still go off. What might cause this to happen?

The door lock actuator (inside door) Door lock switch (on the door) Interior is dealer only. or

Q:Would you buy an ipod or back to school clothes if you had $200 dollars?

No, an oil burner cannot give off CO if not in actual use. However, there are other potential sources of toxic fumes that may be a cause. In no particular order: a) Leaking wax seal at a toilet: This will allow sewer gas into the living area. b) Open trap in a sink, tub, floor drain or other location: Venting sewer gas, as above. c) Cracked soil line or stack (vent): As above. d) Stored VOCs (Volatile Organic Compounds) with leaky containers: Kerosene, naptha, gasoline, paint stripper and any of several other materials. e) Leaking gas - natural or propane: even a small amount can accumulate enough to cause a toxic reaction. f) Poor ventilation: If you are running unvented fuel-fired appliances and do not give them enough ventilation, you may not be getting CO, but you may be depleting the available oxygen. g) At least here in the US, it is pollen season. And, change the batteries in the detector anyway. That way you will be sure it is working.

Q:im having a hard time finding this part (door lock actuator) online and in my local stores does anyone know a good website where i can find it? thank you

If you really want resin, it will quickly get expensive from a paper picture (or computer image) because someone with skill ($$$) will have to sculpt it, then a mold will have to be made ($$) and the figure molded so likely over $1000 These days, if you can create in a CAD program or sculpt it yourself in soft clay which can be scanned, then the figure could be done with 3D printing - but not in resin - at considerably lower cost perhaps under $200

Q:Intel(R) Core(TM)2 Duo Processor T5850 (2.16GHz) or Intel(R) Core(TM)2 Duo Processor P8600 (2.4 GHz)

You can use cement anchors to attach studs to the wall and you can then stuff fiberglass insulation between them just check insulation to make sure its ok to use in damp environment or instead of fiberglass you can use the foam board insulation and drywall over it or leave it exposed until you decide to finish the basement. If you don't want to spend so much on studs you can just glue the foamboard insulation onto the wall with panel adhesive. Then when you finish the basement you can cut into the foam to put the studs in to drywall over.

Q:What is the highest alarm number a fire can be classifiedAnd what makes the differenceThank you.

Did the sample page come out good when you installed the new cartridge? If not check to make sure you removed the plastic strip over the print head.

Q:can an electric blanket catch fire if switched off?

She wasn't punched because she was resisting a ticket. She was punched because she and her friend were assaulting and attacking a police officer. While he was trying to restrain the one girl, the other one would jump on his back, try to grab a hold of him, hit, shove, and push him. What if one of them had tried to grab for his gun? If anything, he showed too much restraint. As a police officer, the minute you have two people physically assault you, grab a hold of you, and try to hurt you, then you are authorized to use whatever force is necessary to halt the attack.

Q:Whether you can do pine boards? Is the resin poisonous and how to remove it?

Softening chopping boardThe boiling water hot panel, and then completely immersed into the salt water board for more than 12 hours, and then use a clean cloth, flat on the chopping board, prevent dry. Repeat several times, until the board is saturated with water, the color is dark red. With the face rub dry, can stick to the residual, and available surface smooth cutting board, surface adhesion surface can also prevent the dry cutting board.

Q:I received a Circo baby blanket back in 2005 when I was pregnant with my daughter. She has since carried that around with since she was born, the blanket was known as blankie. Recently, she has experienced a fire at her fathers house and blankie couldn't be saved. I am in search of this. Does anyone know where I can locate discontinued blankets from them. I have searched all over the net. She is heart broken and I need to find this for her! Thank you for any help you can give.

Place a soda can sideways on a counter.Place your hand on it and push down.The hydralic fluid is the actual pushing force but you get the picture.Appling several tons of pressure is how they can make a car look like a 3' square block of metal.

Q:What's the difference between a resin lens and a traditional lens?

I heard that 710 is also used resin lenses, resin lenses in optical properties and glass lenses vary little, mainly the surface hardness is not high, should avoid unnecessary friction.