Q:does it come in when you go over a certain rpm or do the valves change depending on how far you depress the throtle?

The variable is the valve timing. The spark plug fires a split second before the piston reaches the top of the stroke, to give the fuel a bit of time to burn. But, the faster the piston travels in the bore, that split second gets shorter shorter. So the engine computer changes when the spark plug fires when the valves close, to maximize the power from each ignition stroke.

Q:Water supply pipe gate valve and butterfly valve which good?

2. ball valve: ball valve with a central opening of the ball as the valve heart, the rotation of the ball control valve opening and closing. The ball valve has the advantages of simple structure, light weight compared with the cut-off valve, the sealing surface has the advantages of simple structure, easy processing, good sealing performance, convenient operation, switch quickly, but can not be used to adjust the flow, suitable for high pressure (up to 320 psig) pipeline, at present, the packing material limit, can only be used for 200 DEG C, can also be used a variety of media and the viscosity of the suspension.3. butterfly valve: butterfly valve, also known as turn over plate valve, is a simple structure of the valve. As butterfly valve should not be closely matched with the pipe wall, only applicable to regulating flow, can not be used to cut off the pipeline, often used in conveying air and flue gas pipe to regulate flow. Butterfly valve is with the stem rotation of the circular butterfly plate for headstock parts, in order to achieve the opening and closing action of the valve. Butterfly valve is mainly used with shut-off valve, can also be designed to adjust or cut off and adjust the function. At present, butterfly valves are used more and more in low pressure medium and large diameter pipelines.

Q:What's the material of the butterfly valve seat?

The seating material shall meet the following criteria:1) fluid compatibility, including expansion, hardness loss, permeability, and degradation;2) hardness;3) permanent deformation;4) the degree of recovery after load removal;5) pull in and compressive strength;6) deformation before fracture;7) modulus of elasticity.

Q:What's the difference between a butterfly valve and an eccentric butterfly valve? What is the difference in field applications?

Avoid friction and wear on the sealing surface!And, at the time of closing, and opening the opposite, there is a better sealing effect! Now generally use eccentric butterfly valve as the main. That's all I know! If there is any mistake, please forgive me!

Q:can't locate freon intake valve for 03 jaguar an was wondering were it is located at

Most manufacturers put the fill nozzle on the hoses, either the high or/and the low side. Also, the low side can be found on the accumulator.

Q:The water supply pipe is the gate valve And on the cross dry pipe are the gate valve? To answer the 30

Crown valve pressThere is no standard answer to this question. I can only give you my personal opinionRiser butterfly valve is generally place in these places (the pump outlet valve, drainage system, upper and lower floors) riser are basically installed butterfly valve, butterfly valve is not cheap, fast speed is fast closing butterfly valve can be quickly closed and open educationYou see the water pipe installed valve (with all the cross tube is the basic gate) explanation, because in contrast to the quality and stability, the valve will be better, the site does not need fast switching, it will choose good stability point gateSum upThe drains are all butterfly valves, and the stabilizing pipes are all valves! (do not rule out a full use butterfly valve for stealing work)

Q:I have a 1993 Oldsmobile Cutlass Supreme and I think I have the case of the blow-by. The engine had high mileage, but was rebuilt b/c it stalled while driving. 3.1L V6 gasoline engine. The fuel filter and the fuel pump are brand new. Now we have the same problem a few months later. It stalls while driving. Its been sitting a while and won't start by itself, so I pulled off the air intake hose off of the air filter to spray starting fluid into it. I noticed oil puddled in the air intake hose, so I looked for the PCV valve on the rocker cover. There is a tube going from the air-intake hose to the rocker cover. I popped out the tube from the rocker cover and there is no PCV valve. Just tube. Is that where the PCV valve is supposed to go? If not, where can I find it on the engine? And could that possibly fix the blow-by and the stalling engine? I'd appreciate any help. Thanks in advance.

pcv valve is on the valve cover closest to the firewall.it is attached to a rubber hose that runs to the intake. right below an electrical plug

Q:Are fire fighting signal valves and signal butterfly valves the same thing?

The same nature: both can open and close, there is also information back fed.Signal valves are collectively referred to as signal butterfly valves.

Q:Who was the first doctor to discover Pulmonary Valve Stenosis? Also, who was the first doctor to perform surgery for it? Please and thank you for your help.P.S. I have this condition.

1761 - Pulmonary valvar or valvular stenosis is one of the more common forms of congenital heart malformations and it has been extensively studied since the original description of pulmonary valve stenosis by John Baptist Morgagni in 1761. 1888 - Tetralogy of Fallot, first characterized by Dr.Etienne Fallot in 1888, is present in about 3000 children born each year in the United States. It is a combination of four heart abnormalities. Dodrill and his colleagues employed it with success for the open correction of a stenotic pulmonary valve in October 1952.

Q:What are the uses and classifications of manually operated clip butterfly valves?

In the butterfly valve body cylindrical channel, the disc shaped butterfly plate revolves around the axis, the rotation angle is 0 degrees -90 degrees between, when rotates to 90 degrees, the valve opens the card completely. Butterfly valves are not only widely used in petroleum, gas, chemical, water treatment and other general industries, but also applied to the cooling water system of thermal power stations.