Specifications of Gypsum ceiling
1.Material: incombustible gypsum board,PVC facing, glue and aluminum foil backing
2.Size:600*600,603*603,600*1200 and 603*1206
thickness from 7MM to 9.5MM
3.Surface deal:Normally white color with over 50 kinds of designs such as 154.996.572 etc
Partial color such as 631, full color, silver color and golden color.
4.Edge:only square edge
Personality of Gypsum ceiling
1. Tidy, easy to clean and install
2. various choice with many fashionable design
3. price is very cheap, green products.
Application of Gypsum ceiling
Fasle ceiling in many apartment, factory office, school etc.
Technical data of Gypsum ceiling
HUMIDITY RESISTANT PROPERTY:
UP TO 95% RELATIVE HUMIDITY
LIGHT REFLECTANT PROPERTY:
ACCORDS TO GB8624-1997
Package of Gypsum Ceiling
1.Standard export package, film inside carton outside
2.8 or 10 pcs in one carton
We have 10 production line, 60 containers per month.we have powerful production ability and best price as well as professional team, why not choose us?
- Q:Decoration gypsum board ceiling package package how much money a square
- 80 or so to see the area and shape
- Q:Bathroom gypsum board ceiling did not leave the mouth how to do
- There is no relationship between the maintenance of the hole is not, and now you can directly out of a maintenance hole, you can also need to repair and then check the hole is not too late I hope my solution will help you
- Q:What is the distance between each lamp position on the ceiling of the gypsum board?
- Gypsum board ceiling on each lamp bit spacing should be like this, 2.6 meters three, 4.2 meters four, L-shaped angle is the two sides of the angle of a share of a total of 6 lights.
- Q:Gypsum board putty how long off the drum
- Then we come to understand how the gypsum board ceiling cracking how to deal with:
1. If it is caused by cracks in the cracks, you can first fill with the filling putty, so that the filling putty into the gap inside, can not be limited to the surface of the "entry", the surface was flat and then used to bandage at right angles Gap, and then putty putty, polished after the brush can be latex paint.
2. When the ceiling elevation and beam at the same elevation, the gypsum board must pass through the beam at the end, the advantage of doing so is that there is no interface, which will effectively reduce the seams to prevent cracks. Also handle the ceiling elevation and beam parallel mouth when the gypsum board should be through the lower beam, side of the mouth. Leaving the slit on the side to prevent the seams from present, which would reduce cracks and repair rates. Ceiling wood keel the top corner of the seal gypsum board with L-shaped, to prevent the formation of cracks. Leave the seams on both sides of the ceiling and make the seams in a zigzag shape, then fill the lacquered base or gypsum powder in the joint.
3. has been leveling keel gypsum board ceiling in the external force becomes undulating, resulting in covering gypsum board to produce tension, deformation, cracks. To solve this problem is to pay attention to the construction of the structure and take some necessary measures, such a situation is relatively large harm, and difficult to repair, so that in the construction must be strengthened attention.
4. Gypsum board ceiling cracking can be sewn putty patch, try to let it dry, and then paste seam. Seal putty in the drying process, there may be a small amount of dry shrinkage and dry cracks after the situation, it is recommended in the seam before the tape to pay attention to re-putty again, until dry and then fine sandpaper polished smooth.
- Q:Two gypsum board ceiling is calculated by the square of the square or by gypsum board a square how much money?
- Two gypsum board ceiling calculation, to consider the difficulty of modeling, the number of labor and the number of latex paint and so on.
Normally, the construction process for the double gypsum board + eyebrow paper paste + plaster + latex paint three times more complete.
According to the projection area of the price, then about two square meters it.
- Q:Gypsum board ceiling is the thinnest centimeters?
- The thinnest 5MM there are 7MM there are 1 cm
Suggest you use 1 centimeter
By the time of the test
- Q:Gypsum board ceiling specifications which are detailed
- Gypsum board ceiling specifications are 500 * 500 600 * 600 800 * 800 can also be customized different sizes.
- Q:How to do the ceiling gypsum board
- Process: the roof of the crest of the elevation of a designated keel sub-line a installation of the main keel coins a installation of the keel a installation of the keel a installation of gypsum board (PVC board, health asked) a installation of sealant
(Standard relative height of 2.96 meters, the relative elevation of 26 meters relative to the bathroom), along the wall, the pillars around the ceiling elevation of the standard level.
Installation; main keel pieces: playing a good roof elevation and keel sub-file position line (spacing is not greater than 688mm).
- Q:How to use half water gypsum to make ceiling cracks
- Gypsum board ceiling cracking repair will crack.
In the installation of gypsum board, if there is no installation specifications from the middle to the four sides of the screw, but from the four sides at the same time on the screw, then the gypsum board will produce stress, if the stress is large enough, will cause cracking; Gypsum board screw spacing is too large or some screw position, although correct, but if not fastened, will lead to cracking.
- Q:Ceiling with cement board and gypsum board that board is better!
- There are funds, then select the integrated ceiling, aluminum slab board: environmental protection, safety, durability, taste.
Perfect,a well-known enterprise specializing in the production and sales of Gypsum board and gypsum ceiling, is a direct supplier for CNBM, the wold 500 strong enterprises.
Since the establishment of our company, we have been devoted to setting up a good CIS and completely implementing ISO9001 quality management system.
1. Manufacturer Overview
|Annual Output Value
||Above US$ 10-US$ 50 Million
2. Manufacturer Certificates
|a) Certification Name
3. Manufacturer Capability
|No.of Employees in Trade Department
||Above5000 square meters
|No. of Production Lines
||OEM Service Offered； Design Service Offered
|Product Price Range