Q:How does the rubber part of the watch become yellow?

It is mainly divided into two kinds of natural rubber and synthetic rubber. Natural rubber is made from rubber, rubber and grass. Synthetic rubber is obtained by polymerization of various monomers. Rubber products are widely used in industry or in all fields of life. It has a wide range of uses. [1] can also be divided into rubber with natural rubber, general rubber, styrene butadiene rubber, nitrile rubber, silicone rubber, butadiene rubber, butyl rubber, EPDM rubber, chloroprene rubber types.

Q:Excuse me, what is in the rubber rubber, glue them, what is the difference?

No rubber vulcanization glue all over vulcanization.

Q:Does it work in a rubber factory that causes skin irritations?

Rubber: early rubber is obtained from rubber trees, rubber, grass and other plant latex, processed by the elastic, insulating, impermeable and air material. High elastic polymer compound. It is divided into two kinds: natural rubber and synthetic rubber.

Q:Is there any poison in the processing and testing of rubber products? What about the salary?

There will be some flavor at the time of processing, as well as some fillers, oil will be a little toxic, and some crosslinking agents may be toxic. But now the mixer extruder is mostly closed, so it is common to pay attention to respiratory protection.A mechanical test is usually less toxic, and a glove is enough.If you do thermal testing, such as TGA, DMA, DSC and so on, it will degrade and release small molecules, especially if the aromatic oil is filled, be sure to pay attention to.

Q:Can rubber products be injection molded and plastic injection functions?

Injection molding is a method of producing shapes in industrial products. Products are typically molded by rubber injection and plastic injection. Injection molding can also be divided into injection molding. Die casting method. Injection molding machine (referred to as the injection molding machine or injection molding machine) is plastics molding equipment of thermoplastic or thermosetting material using plastic mold made of various shapes, injection molding by injection molding machine and mold.

Q:Are there formaldehyde in rubber products, too?

Outstanding performance: headache, dizziness, fatigue, nausea, vomiting, chest tightness, eye pain, sore throat, poor appetite, palpitations, insomnia, weight loss, memory loss and autonomic nerve disorder; long-term inhalation of pregnant women may result in fetal deformity, even death, men's long-term inhalation can cause male sperm deformity and death.

Q:Rubber rolling process for making rubber products

The rolling process has become a rolling process.The principle of rolling process: using pressure between the calender roller, the material plastic flow deformation, the final film made with the size and geometry of the provisions of section a section, or the rubber covering process in textile or fabric made of metal surface has a certain thickness of the tape section.

Q:Rubber products are not allowed to touch oil products, but why can rubber gloves be contacted daily? What's the point?

Contact every day is not every day inside the bubble, the contact time is short, the impact on rubber is very small.Raw rubber rubber products are: natural rubber, isoprene rubber, nitrile rubber, EPDM rubber, polybutadiene rubber, styrene butadiene rubber, polyurethane rubber, chloroprene rubber, silica gel etc.

Q:How to remove the peculiar smell of rubber products?

Boiled smell removing method has a long history, has already appeared at the end of 80s, now there is also a part of the factory workshops in using this method (the rubber products produced by cooking in boiling water) this method can eliminate the small part of the reclaimed rubber smell, but most can not eliminate and cannot be eradicated, after a period of time reclaimed rubber continued precipitation and volatile flavor. Boiling water with the exception of flavor, artificial high cost, cumbersome process, the effect can not be sustained, and go to the general effect of flavor.

Q:Process for producing rubber products

There are many kinds of rubber products, but the production process is basically the same. The basic process of rubber products in general solid rubber - rubber as raw materials including: plastication, mixing, calendering, extrusion, molding, curing 6 basic processes. Of course, raw materials preparation, finishing, inspection, packaging and other basic processes are indispensable. The processing of rubber mainly deals with the contradictory process of plasticity and elasticity. Through a variety of techniques, the elastic rubber plastic rubber has become the addition of various additives made of semi-finished products, and then through the vulcanization has semi-finished plastic and rubber products into high elasticity and good mechanical performance.