Q:New standard, how can the pipe joint be labeled, such as "3/4" taper pipe thread?

Pipe fittings 3/4 refers to the pipe fittings of six points (6 British points), DN (diameter) of 20mm, the outer diameter of 26.8mm.Supplement:1 inches =25.4 mm, =8 British points, 1/2 is four points (4 British points), DN diameter 15mm, 3/4 is six points (6 points), DN20mm.

Q:What are the reducing, reducing, reducing, etc in the pipe joint?. How do they tell each other what they call that?. Seek expert advice

The pipe joint is divided into cylindrical pipe thread and tapered pipe thread, and the change of diameter refers to the different diameters of the two ends of the pipe joint

Q:car alarm just goes off.car has problems as it is.

I thought they had uniforms in British schools. If this is the case, that means they have the right to tell you not to wear anything that is not a school uniform. As for French schools, the law doesn't forbid everybody to wear a religious headdress, it forbids the students and teachers to display ostensible religious symbols when they are in the school. This includes religious headdress, kippas, big crosses and a lot of other things, but it's not clothing that are targeted by this law, it's proselytism. This is not an arbitrary ban, this was intended in order to make school more homogeneous and to avoid social segregation based on religion in school. It's actually the same idea than with school uniforms except you have more choice about your clothing.

Q:Why do dogs pee on anything upright? Tree, fire hydrant etc?

Standard water heaters in the US come with 3/4 pipe thread fitings, so 3/4 is what you need. Most plumbers tend to use a torch and solder MPT adapters onto straight copper pipe, but there are fittings that are supposed to make the job easier. There are several reasons why your fitting may not work: 1. the threads on your original fitting might be stripped, preventing the new fitting from getting a good seal. 2. you could be getting a different type of pipe thread from the store. 3. you could be overtightening the fitting when you put it together, One solderless solution might be to use a new product called shark bites. You don't have to solder them, they wokr like a compression fitting, but they go together like ridgid copper. (take a look at the attachment)

Q:cant remove front rotors tried to get off tapping a hammer on backside no luck

Snow tyres are compulsory you will be fined driving without these in both Austria and Germany. Chains you will probably not need them but again it is compulsory to have some with you in case of heavy snowfall which can occur all winter. EDIT Studded tyres or Spikes as we call them in Germany and Austria are banned since at least 20 years over here. You need Winterreifen (S) or Allwetterreifen ( MS) tyres

Q:I don't want to take it to a VW garage if it is something i can do. Please help. Everytime i unlock my car, when i put my key in the ignition the alarm goes off. very annoying.

I wouldn't say that. But they have to change things up or something at some point. And I definitely wouldn't compare this to Nexus. Nexus was crap compared to this, not that there wasn't some talent there, but I thought their gimmick was crap, as well as their theme song, I'm not sure Barret was the best choice 2 lead them either. The Shield has more of the Beginning of the NWO in WCW type feel to it. They're just less well known Professional Wrestlers. But the Talent seems to be there. I think they did a good job with the storyline with them saying that they're not the Nexus or the NWO or any version of any other group that's come back to the WWE. Also I think it's highly unlikely that they've made a storyline that has The Shield working for The Rock or The Undertaker. I do think it would be pretty interesting if that was the case. I think them being aligned with the Rock would be better though. But neither The Rock or The Undertaker make enough appearances in my opinion I just think it would be unlikely. But if that were the case that would be pretty awesome.

Q:The description says its a kesha song, but I cant find it.

The tubing can be bent if you are careful not to try to bend it too short. It will bend easier if you heat it first. You can bend it once and it will start to harden. Just heat it a bit and it will bend easy.

Q:What's the half pipe connection?

The main function is to connect the small main pipe to the big main pipe and reinforce it. The common branch pipe is smaller than DN50, will use half pipe joint, more than DN50, must choose the variable diameter three links to connect.

Q:I should be the system administator for my home personal desktop computer. Why can't I access files etc. that I did not enter into my computer? Thanks for your help!

That's why we have video games like Call of Duty and Killzone 2.

Q:For some reason he keeps waking up in the middle of the night. He never did it before and he doesn't do it when he's having a sleep-over at Grandma's house. He will go to sleep anywhere between 10-11 and be back up at 4 wanting to play. At first I thought he was going through a growth spurt and was hungry, but he never eats when he gets up. My hair is starting to fall out and my house is a wreck. I'm SO tired during the day that I don't feel like doing anything.What do you do when your 14-16 month old wakes up at 4am ready to face the day and play?

Use copper with diletric fittings and insulate them, and you'll never have a problem. Yes it will be expensive but it will be done once and done right. CPVC is good too as it's cheap, easy, and they'll never corrode. PEX or Shark Bite is even easier and may even be better than CPVC as you won't have to deal with messy adhesives and can be done in half the time.