Product Description:
General Information
CMAX high alumina firebricks are classified according to alumina content ranging from 48% to 90%.
Feature
Low thermal conductivity
Excellent acid and base slagging resistance
High refractoriness
Excellent thermal shock resistance
Excellent mechanical strength
Application
CMAX high alumina bricks are commonly used in blast furnace, hot blast furnace, the roof of electric furnace, teeming ladle, rotary kiln, regenerator, etc
ITEM | UAL48 | UAL55 | UAL65 | UAL75 | UAL80 | UAL85 | ALP80 |
Refractoriness, ℃ | 1750 | 1770 | 1790 | 1790 | 1810 | 1810 | 1810 |
Apparent Porosity,% | 22 | 22 | 23 | 23 | 20 | 20 | 18 |
C.C.S, Mpa | 39 | 44 | 49 | 53 | 55 | 60 | 100 |
Refractories Under Load (0.2Mpa)，℃ | 1420 | 1470 | 1500 | 1520 | 1500 | 1520 | 1550 |
Reheating Linear Change,% | 1450℃x2h 0.1～-0.4 | 1500℃x2h 0.1～-0.4 | 1500℃x2h 0.1～-0.4 | 1500℃x2h 0.1～-0.4 | 1550℃x2h -0.5～+0.5 | 1550℃x2h -0.5～+0.5 | 1550℃x2h -0.5～+0.5 |
Al2O3 Content , % | 48 | 55 | 65 | 75 | 80 | 85 | 82 |
- Q:What refractory mortar is better if masonrying 4 meters height and 114 mm width of refractory brick
- Use high aluminum refractory cement!
- Q:What is the best color of refractory brick
- Clay refractory brick: Yellow and deep yellow; acid-proof brick: Red, high alumina brick Beige, a little white; square viewing brick: Yellow, red, white, gray, brown, brown, nigger-brown and so on; color is just one aspect of the selection of refractory bricks, it mainly is to see the inherent quality
- Q:Do refractory bricks resist corrosion and sulfur?
- There are anticorrosion and acid proof refractory bricks
- Q:The matching ratio of masonrying refractory bricks cement
- Size of brickwork joint: Vertical and horizontal seam are 2 ~ 3 mm. The ratio of seam mud: Refractory clay mud 100%; per m3 dry, clean industrial water 400 ~ 600t/, no more than 3mm
- Q:What materials make of clay insulating fireclay brick?
- Clay insulation bricks are general according to the different origins of raw materials, not the same
- Q:how much is the content of the high alumina of refractory brick?
- linear change on reheating is small and Slag resistance is good, matte smelting, good thermal shock resistance used refractory materials should be resistant to high temperature: In front of the furnace, the temperature can reach 1800, copper blowing. The maximum temperature in the smelting furnace area is on the top, pyro-refining and electrorefining, magnesia chrome brick, magnesia chrome castable, magnesia alumina brick. The commonly used refractory materials is direct-bonded magnesia-chrome bricks, which has large volume density. manufacturing technique of copper smelting consists of five parts, Clay brick
- Q:What are the physical and chemical properties of refractory bricks
- The thermal shock stability, linear change on reheating, softening temperature under a fixed load, compressive strength under normal strength refractoriness
- Q:What is the name of the white clay refractory brick
- There are several kinds of white clay, Guangxi clay, Suzhou clay, kaolin
- Q:Development prospect of refractory bricks
- Should increase the intensity of adjusting; masonry method is improper, excessive pressure damages the refractory brick, and its ingredients. In use, to reduce the consumption of refractories clinker. Use pleonaste bricks to replace magnesia chrome bricks directly, after deliberation, the experts present agree unanimously to adopt the draft standard, meet the needs of the new situation, to promote the cement kiln refractory standardization, small thermal expansion rate, fluctuation of product quality, good thermal shock resistance of high alumina brick. Of course, in the process of testing, automation level is low, saving energy. The reasons of refractory life is not high are that the production equipment of manufacturers are out-dated; fine management level is low, some companies began to develop energy-saving products, cultivate leading enterprises. Reduce the heat consumption of clinker tons, which effectively avoid the chrome pollution in the next few years, will promote the elimination of backward production equipment. To increase cooperation efforts on industry, education and research, to promote industry to develop to large-scale and intensification the requirement of firing and fuel In order to solve the problem of short service life of refractory material, the size deviation is large, cement enterprises should take measures aiming at the process conditions and raw material of cement kiln.
- Q:should clay or refractory cement be used to lay refractory bricks?
- structure strength of this brick lining is not good, apply some refractory mud, only use some virgin clay and corundum, many of the traditional approaches are very simple, mullite and carbon slurry, the specific products are selected according to the selected material and water glass or organic binder. binding agent can choose phosphate, silica and high alumina, clay is one part of the refractory clay, there are many kinds of refractory slurry according to the material, clay-based mud does use refractory cement and corrosion resistance is low
1. Manufacturer Overview |
| Location |
|
| Year Established |
|
| Annual Output Value |
|
| Main Markets |
|
| Company Certifications |
|
2. Manufacturer Certificates |
| a) Certification Name |
|
| Range |
|
| Reference |
|
| Validity Period |
|
3. Manufacturer Capability |
| a)Trade Capacity |
|
| Nearest Port |
|
| Export Percentage |
|
| No.of Employees in Trade Department |
|
| Language Spoken: |
|
| b)Factory Information |
|
| Factory Size: |
|
| No. of Production Lines |
|
| Contract Manufacturing |
|
| Product Price Range |
|
