Butterfly Valve Without Pin Ductile Iron DN110

Ref Price:

Loading Port:: Tianjin

Payment Terms:: TT OR LC

Min Order Qty:: 50 set

Supply Capability:: 50000 set/month

Inquire Now

Add to My Favorites

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

You Might Also Like

Ductile Iron Ventilation Butterfly Valve DN50--DN3000

Butterfly Valve Isolating or Regulating Flow U Type FF RF Pisition-Off 360 ISO 5211

butterfly valve Duplex valve

Butterfly Valve The Pin Spline or Square Connection China

Resilient seated double eccentric flanged butterfly valve DN40-DN1800

Butterfly Valve DN80 Turbine Type Hand Wheel

Butterfly Valve DN500 BS5163 Made in China Britain Standard

Butterfly Valve DN650 BS5163 Stardard Low Price

Centerline structure,pinless double half shaft design.
Disc has two-way bearing, no installation direction requirements.
Non-backed replaceable seat with good performance and a longer working life.
Square and short neck for lable use and cost saving.
Easy installation, no need flange gasket.

Size	DN50mm-DN600mm
Design standard	API609/EN593
End flange	DINPN10/PN16, BS4504PN10/PN16, ANSI class125#/class150#
Face to face	API609/EN558-1
Top flange	ISO5211
Body	Ductile iron/Cast iron
Disc	Ductile iron/CF8/CF8M/C95400/C95500
Stem	SS420
Seat	EPDM/NBR/Viton/PTFE
Actuator	Bare shaft/Lever/Gearbox and handwheel
Coating	Epoxy/Nylon/PTFE
Pin	With out pin
Suitable medium	Water/Seawater/Sewage/Air/Foodstuff/Oil

Q: Transformer butterfly valve and pressure relief valve difference: I don't know. Let's have a Baidu! Baidu is powerful.

Q: What is the meaning of the D341*5-10 / 16ZB1 turbine butterfly valve flange said?: Liu1964tg, this guy is right, don't know, don't mislead everybody

Q: What are the advantages of butterfly valves?: Butterfly valve, also known as shutter valve, its advantages are:A. has a large circulation capacity and is about 1.2 times the same size as two seat valves;

Q: How can the flange butterfly valve be installed on the pipe?: Direction.Butterfly valve in theory can be installed in any direction, it is recommended that the horizontal installation of the valve shaft installation, so that both ends of the bearings will not be at the bottom (below), so as to avoid sediment in the media into the bearing.Inlet pipe configuration.There are water inlet side valve elbow, tee pipe fluid caused by bending and uneven distribution of the inflow valve, the drift will occur in the pipe, so it must be generated by the uniform drift disposed on both sides of the disc, so as to avoid uneven force on both sides of the disc, and may produce additional torque.

Q: Butterfly valve D71X-1.6C, DN50, there is no difference between C and no C? What do you mean by "concrete"?: Front is the same, there is C refers to the body of the material is carbon steel, without C, usually refers to gray iron (cast iron is more common, so are generally omitted)

Q: what are the step i need to do so i can change the valve seals my truck has been smoky.,,, any websites i want todo it myself... 1989 chevy silverado 2500 350 engine 5.7L: First find out if that is the issue. Do a wet/dry compression on all the cylinders. That is where you do a compression test on all the cylinders and write them down. Then squirt about three pumps of oil from a oil can into each cylinder and retake the compressions. If the compressions don't change and are low, the valves are burnt and you need a valve job. If the compressions go way up after the oil seals the rings, then the piston rings are bad and the engine needs rebuilding and that may be where the oil smoke is coming from. If all the cylinders are within 20 psi and runs good, then it may be your valve guide seals are bad. You can replace them without pulling the heads. You can go to an auto parts store and buy a valve spring compressor that is used while the head is on the block. It has an air fitting that screws down into the spark plug hole and when filled with compressed air, holds the valves up while you remove the spring and replace the valve guide seal.

Q: can't locate freon intake valve for 03 jaguar an was wondering were it is located at: There is no Freon intake valve for an 03 Jaguar. Freon is R12 refrigerant and the vehicle uses an R134a refrigerant system. There is also no such thing as an intake valve on any vehicle refrigerant system. There is a high pressure port and a low pressure port. To answer your question: under the hood. Any other information would likely endanger your life, since this is obviously a DIY question and you lack the knowledge to safely recharge your vehicle's refrigerant system. R134a refrigerant, if inhaled, can kill you. Do not turn a DIY project into a DIE project. Leave the complicated stuff to the professionals.

Q: What's the difference between electric butterfly valve and electric two way valve?: Below we will be specific to understand the electric two way valve and electric butterfly valve of the difference between.Distinguish one: product performance is different, the electric two way valve is for the central air-conditioning fan coil supporting products; and electric butterfly valve and electric control valve is the same species;Difference two: the product function is different, the electric two way valve is automatic adjustment; and the electric butterfly valve is a variety of adjustment methods.Difference three: product classification is different, the electric two way valve body activities are more piston style structure; and butterfly valve structure is diversified, such as sealed form can be divided into soft sealing and hard sealing type of two.

Q: Butterfly valve D71X-16 and D71X-16Q what is the difference?: The two difference is that the body of the material is not the same, 16 behind with no sign, expressed as a default, is carbon steel (usually C), if you need to specify material, just behind with symbols, such as Q nodular cast iron, stainless steel P.

Q: Buried extension butterfly valve is buried or need to repair the valve well, can build the valve well, the extension rod butterfly valve installed in the valve well, the extension rod to avoid covers, the top of the valve well out, so that the hand wheel in the ground operation.Atlas S143 is less than the inner diameter of DN150 valve wells only 1200mm, DN200-DN250D diameter of only 1400mm, 700mm valve covers, valve rod and a handwheel to lengthen through the valve cover, valve wells is built to cover the embedded pipe or tube? Is there a standard atlas?: It's better to get a valve well for future maintenance.

Send your message to us

*Email

*TEL

*Quantity

*Unit