4 O Aluminum Wire AA5052 0.05mm-0.95mm for Mesh

Inquire Now

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

You Might Also Like

Descriptions Of Product Aluminum Wire

Product		Pure aluminum	Corrosionresisting aluminum alloy
Brand		YH-301	YH-331	YH-5356	YH-311
Standard and steel grade	GB	S301	S331	S5356	S311
Standard and steel grade	AWS	ER1100	ER5183	ER5356	ER4043
Gauge Φ(mm)		0.8-5.0	0.8-5.0	0.8-5.0	0.8-5.0
Welding wire chemical composition(%)	Cu	0.05~0.20	≤0.10	≤0.10	≤0.30
	Si	≤1.0	≤0.40	≤0.25	4.5~6.0
	Fe	-	≤0.40	≤0.40	≤0.80
	Mn	≤0.05	0.05~1.00	0.05~0.20	≤0.05
	Mg	-	4.3~5.2	4.5~5.5	≤0.05
	Cr	-	0.05~0.25	0.05~0.20	-
	Zn	≤0.10	≤0.25	≤0.10	≤0.10
	Ti	-	≤0.15	0.06-0.20	≤0.20
	Al	≥99.5	Rem	Rem	Rem
Application	YH-301	Good plasticity,primarily used for gas welding and argon-arc welding of corrosion-resisting pure aluminum
	YH-331	High strength,good corrosion resistance,primarily used for argon-arc welding of aluminum alloy
	YH-5356	Outstanding corrosion resistance,high strength,exceptional versatility,,primarily used for argon-arc welding of aluminum alloy,especialy for 5083 aluminum alloy
	YH-311	Outstanding corrosion resistance,exceptional versatility,primarily used for welding and MIG welding of aluminum alloy,especially good for 4043 aluminum alloy ,Not recommended to use for welding of magnesium alloy.

Q: Copper wire drawing machine with copper wire drawing machine, what is the difference: The power wire drawing machine drawing machine motor copper clad aluminum a little smaller, because the tensile strength of copper clad aluminum is relatively small

Q: LV how to solder, seek expert advice, please everybody: Loading wire to welderThere is a knack for correctly loading aluminum wire (also applicable to steel wire), which is very important for loading aluminum welding wires and avoiding welding failures. Hold the wire shaft safely with one hand to make sure it won't let loose. Once you open the cellophane wrapper, hold the loose end of the wire with the other hand before you put it into the drive wheel. Inexperienced people usually fail to grip the loose end and cause the entire bundle of wires to start loosening. If this happens, it will not be remedied and welding operations will be greatly affected - you will have to buy another bundle of wire.

Q: Pure copper wire for 1 points and 2.5 copper clad wire which is better?: Copper is good, I guess the 1 of your family is to change the electricity, the rest of the bar, in order to clean up, use 3*1.0 (RVV)

Q: In the process of spark discharge machining, why hasn't the aluminum wire been fused by the high temperature produced by it?: If it's a question, it's a question of molybdenum wire, not aluminum. You take a closer look........ That is the reason why the fuse is not tungsten molybdenum wire is synthesized, with characteristics of high temperature resistant tungsten, molybdenum also has the flexibility of the process, a cooling liquid cooling, so high temperature fuse will not be generated

Q: Isn't there something inside the wire like a wire?.: Because of the electrical conductivity of iron is not good, the general wire are copper or aluminum wire, copper wire and aluminum wire conductivity is good, however, the anti bending performance of it is not good, if the regular drag of the occasion, in the aluminum wire and copper wire is easy to break, in order to strengthen the anti bending capacity of cable usually, in Riga strands of a copper wire, if the wire broke, in this part it is easily broken, but if broken in the interface area, the problem is not too much.

Q: How to tell how thick the wire is?: The so-called square, refers to not square meters, but square millimeters. The copper wire in the middle of the wire, the aluminum wire, is round, and these rounded section area is the square of these.

Q: How to process aluminum wire into 0.1 mm aluminum wire, and the efficiency can not be too low: Particles in a millimeter, in addition to grinding, there is no other, the more the better

Q: How to bind overhead wires?: A wire is a component used to conduct electricity and to transmit electrical energy. Overhead bare wire is usually one phase, 220kV and above line, because of the large transmission capacity, at the same time, in order to reduce corona losses and corona interference, the use of phase split wire, that is, each phase using two or more wires. The split conductor can deliver larger electric energy, and it has less power consumption and better anti vibration performance. The conductor is often tested by various natural conditions in operation. It must have the characteristics of good conductivity, high mechanical strength, light quality, low price, strong corrosion resistance and so on. As China's aluminum resources than copper rich, coupled with aluminum and copper prices vary greatly, so almost all use steel cored aluminum stranded wire.

Q: Which is the best wire, a few thin copper wires and a thick single aluminum wire?: Of course, the multi strands are good, the electrons have surface effects, and the surface areas of the strands are large. Copper conducts electricity more than aluminum does!

Q: When fuse is blown, why not use copper wire and wire instead?: Because copper wire, wire resistance is too small, and higher melting point, when the current is too large, can not fuse in time, so it can not replace the fuse

Send your message to us

*Email

*TEL

*Quantity

*Unit