Anderson Roofing

Hot Products

Gypsum Board Good quality Low Price Acoustic Perforated

Gypsum Board ( Plasterboard ) For Wall

Gypsum Board Good quality Low Price Acoustic Perforated

Gypsum Board Cheap Roofing Material Fireproof Exterior Wall Panels

Cheap Price Gypsum Board with Standard Size Factory

Gypsum Board Cheap Roofing Material Fireproof Exterior Wall Panels

Moistureproof fireproof wave decorative gypsum board

Paper Faced Gypsum Board Manufacturers in China

Gypsum Board The Standard For Wall Partition

Gypsum Board/ Drywall/ Plasterboard / Interior Wall Panel

FAQ

Gypsum board after the ceiling how to brush white ah?

Gypsum board ceiling: 1, the use of light steel keel according to the design requirements, or modeling or put down the light steel keel, 2, the gypsum board with self-tapping screws fixed on the dragon skeleton, 3, oil workers use anti-rust paint will be fixed by a point brush, 4, the use of elastic putty gypsum board and gypsum board patchwork (installation of gypsum board, the patchwork must stay 8-10 mm gap) leveling, naturally dry. 5, with a special gypsum board sealed with a latex paste paste in the gypsum board and gypsum board patchwork, naturally dry. 6, and then putty after 2-3 times leveling, grinding process until the smooth and smooth, 7, brush the first series of latex primer, naturally dry. 8, in the rolling brush 2-3 times the latex finish can be.

9 meters, the closet to do 2.4 meters high and then gypsum board cap or directly to the top of the rough layer height of about 2.9x meters

It is recommended that the following wardrobe do 220cm high overall moving door, do 60cm high top cabinet (storage cabinet) with cabinet board to do the door, especially practical.

I installed the lights on the gypsum board on the screw, not the kind of embedded lights

Looking for gypsum board ceiling when the position of the dragon skeleton, in the position of the keel installed lights, and now the lamps are relatively light as long as you can screw the screw on the keel it certainly no problem.

I would like to ask how much small gypsum board machinery

The price should be tens of thousands to hundreds of thousands. Depends on the machine you choose. Low price may be high labor costs.

Causes of Cracking of Gypsum Board Ceiling Joint and Its Treatment

Gypsum slab processing steps and specific methods: 1, to ensure that the gypsum board gap at the keel, and self-tapping uniform fixed; 2, set aside enough slit - generally 3-5mm; 3, with gypsum powder or fast adhesive powder to seal the gap, to be dry; 4, with white latex paste caulked belt - note the zipper inside and outside sides of the brush, to be dry; 5, then scraping putty or imitation porcelain.

Gypsum board hanging before the top and the wallpaper before the paste, must be putty putty?

Process flow Grass-roots treatment → full scratch putty twice → the bottom of the paint → middle paint twice → latex paint spray → cleaning.

Duplex structure of the house, the lower part of the compartment hanging gypsum board ceiling problem

I do not recommend directly fixed on the I-beam, the correct approach is welded in the I-beam hanging bars, and then hanging the main keel, the main keel layout, the vertical arrangement of the vice keel, so more reliable! The so-called dovetail is a screw from the drill bit, more suitable for 1.5MM within the steel plate fixed.

Gypsum board to do the wall above is the wallpaper or brush latex paint price is reasonable

If the landlord is to buy a wallpaper, then you can go to your local building materials market to see ah, the general wallpaper brand in the local building materials market are distribution outlets, outlets are generally from the original purchase, the quality can still trusted. Recommended Ruibao wallpaper, a considerable environmental health, sent the master of the process Ye Hao, the service is more thoughtful.