Q:The difference between butterfly valve d71x_10s and d341s-10

Before distinguishing between the two, you must first read the identification of the valve type:D stands for butterfly valves,3 means that the worm gear is connected and the drive does not indicate the handle7 and 4 indicate pipe to clamp connection, pipe flange connection, respectively1 means single eccentric, that is, the stem is not in the center of the butterfly plateThe former S indicates the material name of the valve body - plastic, X means sealing and the lining material is rubberThe latter S indicates the sealing lining material code ---- plastic, and the valve body is cast iron.10 means stress.

Q:What does the model D373H-16C of butterfly valve mean?

D373H-16C said: D type butterfly valve butterfly valve 3 said, said 7 of the turbine, said clip, 3 said the three eccentric (swash plate), 16 C nominal pressure, said carbon steel. In fact, if you want to understand this, to understand the valve 3.07ghz, later met have to be attached to the valve. 3.07ghzModel for valves, valve number indicates valve type valve should normally be that type, drive type, connection type, structural features, nominal pressure, sealing surface material, body material and other factors. Standardization of the valve type of valve design, selection, distribution, provide more convenient. The type of valve types and materials are more and more more models of the preparation of the valve will become more and more complicated. Although the preparation of our valve type unified standard, but gradually can not meet the needs of the valve industry. At present, the valve manufacturer usually adopt a unified numbering; not uniform numbering, the manufacturer can make out no.methods according to their own situation. Unit two unit three unit four unit five unit six unit seven unit

Q:I went online to check where was the pcv valve for a 2001 ford focus, but I didn't find it. Does anyone have a picture? Thanks

The PCV (positive crankcase valve) is usually on top of the engine or in the valve cover, but it will be in different locations depending on the engine cylinder count: 4, 6, or 8 cylinder. You may have to go to a dealer and ask for a parts breakdown drawing which will show you where all the various parts are located. Some libraries have big books that show all the details about any model of car. Ask around.

Q:How can the flange butterfly valve be installed on the pipe?

Direction.Butterfly valve in theory can be installed in any direction, it is recommended that the horizontal installation of the valve shaft installation, so that both ends of the bearings will not be at the bottom (below), so as to avoid sediment in the media into the bearing.Inlet pipe configuration.There are water inlet side valve elbow, tee pipe fluid caused by bending and uneven distribution of the inflow valve, the drift will occur in the pipe, so it must be generated by the uniform drift disposed on both sides of the disc, so as to avoid uneven force on both sides of the disc, and may produce additional torque.

Q:valve adjustment 2001 chev prism 1.8L

valve adjustment . you need to know the fire order. the gage between the stem. rotators the cranshaft. it could be cold start. cylinder need to be bottomed center.

Q:CAD drawing of butterfly valve

Your question is very international. Ha-haThis method of painting is not clear in one or two words.First you'll know the map, then you'll use CAD, so the two will add up.Guess you will.

Q:When i waa replacing the valves in the las 4 valves , they dropped and i dont know how to make them go back up, and i dont want to take the engine out of the car, is there any tool to make the valve go back up or there is any way to do it?? People told me that i can crank it by and , but i dont know how to do it where do i have to do it, i need help please im begging for help!

Asking okorder /

Q:How do the butterfly valves d341 and d343 differ in appearance?

Under normal circumstances, 41 is soft seal body, 43 is hard sealing valve body

Q:What is the difference between turbine butterfly valve and flanged butterfly valve?

The worm gear is the driving mode and corresponds to the handle; the flange is connected and corresponds to the clamp. Flange worm valve is generally, the handle of the butterfly valve

Q:16 inches below the choice of electromagnetic valve can be the same, it turned out to be DN200 election 1/4, and now there are DN350 can also use this? With it, limiter, pressure relief valve, locator model will change?

This is our company's products in Pucheng clean energy Co., Ltd. successful use case, if you need case details, you can give me a QQ number, I sent you. In addition, I suggest you add a pneumatic control valve, so that the safest, no map, I can give you. Saved is to look at the project site, if the north, the electromagnetic valve is recommended to use the 1/2 aperture, and a gas control valve or 1/4, it can guarantee the opening speed of the valve, special attention is on the use of the electromagnetic valve chain, this is very important, I will be the general experience specific issues to deal with specific, can not copy blindly, in most cases, this is no problem. And 1/4 also to see traffic, is also 1/4 solenoid valves, flow valve with big caliber is not the same, is not the same, the 1/4 path from the 2mm-12mm range, the CV value is small, about 0.1, with a large amount of 1.2, has big gap, valve opening time is also a great gap, to distinguish between the.