Butterfly Valve DN80 D43H-16C D73H-16C D343H-6C D343H-10C

Ref Price:
Loading Port:
Shanghai
Payment Terms:
TT OR LC
Min Order Qty:
10 unit
Supply Capability:
500 unit/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Butterfly valve, also called the flap valve is a kind of simple structure of the regulator, 

also can be used in low pressure pipeline medium valve butterfly valve in the switch 

control the way work is closed a (disc or disc) is a disk, around the axis of rotation to

achieve a valve open and close, mainly in the line cut off and throttling effect.

Butterfly valve opening and closing is a disc-shaped butterfly plate, the body rotation 

around its own axis, so as to achieve the aim of opening and closing or adjust.

Introduction to the

Butterfly valve, butterfly valve) : also called butterfly valve worm gear
Definition: open-close part for disc butterfly plate and a valve body axis rotate.[1]
Structure: mainly by the valve body, valve stem, disc and seal ring.The body is 

cylindrical, short axial length, built-in butterfly plate.
Using range
Electric butterfly valve butterfly valve is suitable for the generator, gas, 

natural gas, liquefied petroleum gas, city gas, cold hot air smelting, chemical 

industry and power generation, environmental protection, such as, building

water supply and drainage engineering system of conveying a variety of corrosive,

non corrosive fluid pipe, used to adjust and block the flow of the medium.
Functional purposes
Pneumatic butterfly valve butterfly valve (English: butterfly valve) is to point 

to shut down a (disc or disc) is a disk, around the axis of rotation to achieve 

a valve open and close, mainly in the line cut off and throttling effect.Butterfly 

valve opening and closing is a disc-shaped butterfly plate, the body rotation around

its own axis, so as to achieve the aim of opening and closing or adjust.Butterfly valve 

fully open to the barrier is usually less than 90 °, butterfly valve and the adjustment 

lever itself has no self-locking ability, in order to butterfly plate positioning, to add 

worm gear reducer on the valve stem.The use of worm gear reducer, can not only 

make the butterfly plate with self-locking ability, make the butterfly plate to stop at

any position, also can improve the performance of the valve.Industrial specialized 

characteristic ability of high temperature butterfly valve, apply pressure range is higher also, 

nominal valve size is big, the body is made of carbon steel, valve plate seal using metal ring 

instead of rubber ring.Large high temperature butterfly valve USES the steel plate welding 

manufacturing, mainly for the duct smoke and gas of high temperature medium.

 


Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:The difference between the electric control valve and the electric butterfly valve, respectively, the application situation
Electric butterfly valve is a kind of electric control valve.There are many types of valve body, usually through the single seat, straight through two seat, angle, diaphragm, small flow, three pass, eccentric rotation, butterfly, sleeve type, spherical and so on 10. In the selection of control valve valve prior to the media, process conditions and parameters to control the process of careful analysis, to collect sufficient data to understand the system requirements on the control valve, according to the data collected to determine the type of valve to be used.
Q:D341W-10P-400 butterfly valve, what does each alphanumeric letter mean?
According to JB/T308-2004 "valve type programming method"D butterfly valve3 worm gear4 flange connection1 Structure: sealed type, central vertical plateW sealing material for valve body material10 nominal pressure PN10P body material is chromium nickel stainless steel400 shall be nominal size DN400
Q:What kinds of butterfly valves are available? What is the working principle of butterfly valves?
According to the form of sealing:(1) forced sealing butterfly valve.1) elastic sealing butterfly valve. The pressure of the valve seat, seat, or plate is produced when the seal is closed by the pressure from the valve.2) additional torque seal butterfly valve. The seal is produced by a torque that is applied to the valve shaft.(2) pressure sealed butterfly valve. The pressure is greater than the pressure on the seat or plate.(3) automatic sealing butterfly valve. The pressure of the seal is automatically generated by the pressure of the medium.Divided by work pressure:(1) vacuum butterfly valve. Working pressure is lower than the standard atmospheric pressure butterfly valve.(2) low pressure butterfly valve. Butterfly valve with nominal pressure PN<1.6MPa.(3) medium pressure butterfly valve. Butterfly valve with nominal pressure PN 2.5--6.4MPa.(4) high pressure butterfly valve. Nominal pressure PN is 10. 0--80.0MPa butterfly valve.(5) ultra high pressure butterfly valve. Butterfly valve with nominal pressure PN>100MPa.
Q:How to control the single acting pneumatic butterfly valve?
Single acting pneumatic butterfly valve can be divided into gas open type and gas closed type, which is usually called "normally closed" and "normally open". This is very critical. The single feature pneumatic butterfly valve is the biggest feature of its spring reset function, when the loss of gas or sudden failure, you can automatically restore the original state. So it's important to open the air or air this time.
Q:What is the national standard for clip butterfly valves?
GB/T 12238-2008 "flange and clip connection elastic seal butterfly valve"GB/T 26144-2010 flanged and clip on steel lined fluoroplastic butterfly valvesJB/T 8527-1997 "metal sealed butterfly valve"
Q:mitral valve prolapse?
I have Mitral Valve Prolapse, and slight regurgitation. If your cardiologist says not to worry, I wouldn't worry. Mitral Valve prolapse just means you have a slight deformity of the bicuspid valve. It doesn't close correctly. It's not a disease, or anything like that, just a slight deformity. The symptoms are annoying. You may or may not have palpitations, slight sharp chest pain sometimes, dizziness, fatigue, and anxiety from it. You must have it checked yearly to make sure it's not progressing. I have had it since I was born, and now I am 28, and it has not progressed at all. MILLIONS of people are walking around with it, and don't even know it. It's not really a big deal. However, it does have the potential to worsen and you may or may not need a new valve. But that normally happens when you're older, in your 50's or up. Don't worry about it.
Q:Big block, solid lifter, valve clearances?
Because you apparently have a built engine here rather than a factory assembly which simply has solid lifters, and the data you have is either inconclusive or conflicting then I will recommend the following procedure: Assemble them cold and adjust to Intake .010 and exhaust .020. After firing up the engine, adjust the carb, if it is so equipped, to a smooth rich idle and run it in for a couple of hours mixing idling with moderate load and a few full throttle pulls through 2nd gear to seat the rings. Bring it back into the shop good and hot and set the valve clearances at .008 intake and .016 exhaust hot. After adjusting the valves readjust the idle to 700 RPM and set the timing. initially set the timing at about 2 degrees BTDC until you hav run in the engine, If you are without clear specifications for timing use a vacuum gauge and play with it between 2 and 10 degrees BTDC with the vacuum advance disconnected and plugged, you are looking for the highest vacuum at idle as a starting point. Run it hard including lugging it in high gear at around 2500 to 3500 rpm at or near full throttle, if you are getting spark knock back it down 2 degrees at a time until it does not knock when lugged. If you get no spark knock when lugging it you might try advancing the timing 2 degrees above the vacuum indicated optimal setting but do not go beyond that point. After setting the valves and timing readjust the carburetor to the best lean idle and set to 650 to 700 rpm depending on where it feels comfortable. In the old days a lot of this was done totally by ear - hence the term engineers. Today I think most holders of that revered title do not have a clue where the term came from.
Q:What are the butterfly valves models?
Divided by connection:1 pairs of clip butterfly valveThe butterfly plate of the clip butterfly valve is installed in the direction of the diameter of the pipe. The valve is fully open.The clip butterfly valve is simple in structure, small in size and light in weight. Butterfly valve has an elastic seal and metal seal two types of seals. Resilient sealing valve. The sealing ring can be mounted on the valve body or attached to the periphery of the disc.2, flange butterfly valveThe flange butterfly valve is a vertical plate structure, and the stem is a sealing ring of an integral metal hard sealing valveFor flexible graphite plate and stainless steel plate composite structure, mounted on the valve body, butterfly plate sealing surface of stainless steel surfacing. The sealing ring of the soft sealing valve is made of nitrile rubber and is mounted on the butterfly plate.3, lug butterfly valve4 、 welded butterfly valveWelding type butterfly valve is a non sealed butterfly valve, widely used in medium temperature less than building materials, metallurgy and mining, electric power production process at 300 nominal pressure 0.1Mpa pipe, used to open and close connected, or adjust the medium quality.
Q:Especially butterfly valve
Butterfly valve headstock is a disc shaped disc, in the valve body around its own axis rotation, so as to achieve the opening or closing or adjustment; actuators have electric or pneumatic, and so on, through the transmission device to drive the stem, valve plate rotation;
Q:Can I reuse intake & exhaust valves?
If the valve is burnt there is no longer something you're able to do with it yet replace it. in the event that they simply desire cleansing up you could lap them in with a lapping compound the threat with this is which you would be able to desire to visual exhibit unit which you don't get close to to the sting of the valve, this is once you will finally end up with a burnt valve. The valve should not be flush with the valve seat this is plenty to close and the warmth of combustion could have an more advantageous effect on the textile.

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range