Q:like lets i want to want to connect my speaker wires with other wires can i use elmer glue so that it sticks and will the wires still work?

You could always solder it, but no, glue won't allow electricity to pass through.

Q:I want two lights on two 3-way switches.1. Power from basement box into light #1 with 12-2 wire. 2. Another 12-2 wire from light #1 to light #2.3. A 12-3 wire from light #1 to switch #1.4. Another 12-3 wire from light #2 to switch #2. Will this do it?

nevermind what I think....the guy under me knows EXACTLY what he is talking about! Do it exactly like he says. His way is better than mine was, honestly, because he has more experience. Thats why I deleted my own answer----we call that professional courtesy to seniority and its what electricians do when someone has more experience than we have speaks up. Now it doesnt matter what I think....I only have 22 years experience and someone with more experience than I has given better, sounder advice than I did. You should listen to him, not me.......or anybody else whom cannot match or exceed his experience. Or didnt you know that all Electricians are part of the same Brotherhood? This is why we always agree (or agree to be wrong). I was wrong, obviously, and my advice, second rate, compared to the advice you are about to get. So.....Pay attention! Wisdom follows!!!!

Q:i just got two new aiwa stereo speaker's they come with their own wiring in the back but i dont know which wire is whatthere is one black wireand there is another black with gray dashesim thinking the one with dashes is positive?the speaker works both ways

I wouldn't worry about polarity too much with those speakers. You're never going to be able to hear a difference, and your amplifier isn't going to care.

Q:u said when i buy a jvc wiring harness one end plugs in the back of cd player and the wires coming out of that connect to the wires in car will they be the same color though? right now there is a harness already on the cd player and the wires are on it and they are pretty long i thought i just wire those wires from it to the ones in car but they diff. colors

wait wait . u must buy the wiring harness that correspond to ur car first. than u wud simply wire the new wiring harness u bought to ur deck and simply match the colors. and than u simply connect it to ur existing car harness. baaamm done .

Q:do i need a different wire for in-wall speakers or a regular speaker wire

Regular speaker wire will work for in-wall speakers.

Q:Ok I've been changing the old outlets in the house and all of them were fine until I got to this 1 outlet. The outlet had 1 ground wire, 2 white and 2 black (if that helps). The wires were a little chewed up looking so when I went to wrap the upper white wire to its screw it broke and now the wire won't reach the screw and certain lights in the house won't turn on because of it. I probably should have left it alone because of the condition of the wires but its too late now so how do I go about getting the wire to reach its screw ? Thanks

The white wire can have a 6 inch* pigtail extension attached to it at the same you spice them together with a wire nut or crimp followed by taping. I'm wondering about the two hot wires though. You didn't say if they too broke apart or were connected separately to the old outlet. If they broke, the same thing can be done for them as you would the white (common) wires. If one half of the old outlet was isolated to respond to a light switch, there's a small break off piece on the outlet that needs to be taken off before you connect them. If you have a meter or a neon tester, it would be good to see which one responds to the switch if you don't know by now. If they were both connected to the outlet without isolation, pigtail them as you did the common and connect one wire only. (The outlet shouldn't be used as the connector between two wires. It wasn't designed for this.) Finally, wrap a couple of turns of tape around the outlet to cover the screws that the wire connects to as it will make further service safer. As most jacks are well marked for polarized hook up, it's hard to see what the writing (if any) is on the back even in good light. Remember the short slot runs hot. Somehow, that's always been the easiest way for me to not forget. *More if you need and there's room in the box. But 6 is standard.

Q:How do you attach light wires to boat trailer frame?

If your frame is hollow, use a fish to bring the wires through the frame. Some things you want to watch out for is corrosion of the trailer, and the wires flapping in the wind, or the wires snagging on something when trailering. That being said if you have to mount the wires externally use enough enough clips to keep the wires snug to the trailer. Be sure to seal the holes you drilled for the clips with silicone or rust preventive paint. If you can go through the frame internally, you need only secure the wires with clips at entry and exit points.

Q:I don't like wiring nuts because I always feel like it's not a solid connection, like it could come out.

This Site Might Help You. RE: Is there an alternative to wiring nuts? I don't like wiring nuts because I always feel like it's not a solid connection, like it could come out.

Q:im throwing in a radio in my 2002 f-150 and i need the color codes for the truck radio wires

buy a wiring harness for your particular veh. it,s color code. very simple you won,t have to cut your wires. so you can always just put stock radio right back in.

Q:hi can anyone help i am currently building a 50cc scooter up from scratch i have most parts but ive started on the wiring does anyone know where i can get a wiring diagram also what wire recharges the battery from the magnetic pickup thanks

Here okorder /