Forged steel Tee NPT DN25 3000LB A105 ANSI B16.11

Ref Price:
Loading Port:
Shanghai
Payment Terms:
TT OR LC
Min Order Qty:
-
Supply Capability:
-

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

available in class 3000, 6000 and 9000 (high pressure) socket weld fittings;
also, in class 2000, 3000 and 6000 threaded fittings.

Tee
1/8" to 4" class 2000 threaded
1/8" to 4" class 3000 threaded & socket weld
1/8" to 4" class 6000 threaded
1/8" to 4" class 6000 socket weld
1/2" to 2" class 9000 socket weld

Material:

CS: A105

AS:A182F5 A182F9 A182F11 A182F22 A182F91

SS:A182F304/304L A182F316/316L A182F51 A182F53 A182F60

Standard:ASME/ANSI B16.11 BS3799 GB/T14383

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:The name of the card sleeve joint
Or 1 inch single (head) card sleeve and 1 inch double (head) card sleeve
Q:Is the trachea connected directly to the inside and outside threads? I remember a sealing ring
The question is too abstract:#1: if the pipe thread (G, NPT, BSP), only need to use raw tape or liquid TEFLON coated, tighten can be.#2: some joints are sealed by the cone. Sealed by a cone (of a ferrule); some have O rings, others are straight. You can find it on PARKER's product samples.#3: some connections are screwed with M thread. Seal by type O ring or copper gasket. You go to FESTO, SMC's website to find the M thread connector, you can.#4: there are other types of fast couplings, too. There are too many kinds.
Q:What's the difference between the half pipe joint and the branch seat?
The 2. branch pipe seat is widely used abroad in recent years, the branch for strengthening pipe connection, to replace the traditional use of different diameter three, reinforcing plate, strengthening pipe etc. branch connection type, which has the advantages of safety, lower cost, simple construction, improve media channel, standardization, series design has the advantages of convenient so, especially in high pressure, high temperature, large diameter and thick wall pipe is widely used, instead of the traditional branch connection method
Q:Stainless steel pipe, wire joint leakage how to make up?
What is the pressure in the pipe? The glue material is not blocked up, in the humid environment and water under the condition that the glue is not stick, reliable and economic way: cold metal flux were patching, simple and convenient, do not need what tools
Q:How many bonding methods are there in the belt joint?
3. heat curing joint, the heat vulcanizing joint conveyor belt interface is completely closed, not susceptible to water wetting. Technology of belt vulcanizing joint is generally placed on the belt vulcanizer frame under the frame, both ends of the alignment, then put on the pressure plate, small thermal insulation board, insulation sheets, two vulcanizer installed on each side of 1-2 meters of the platform and fixed platform, the upper surface to the lower heating plate and flat surface homogeneous or slightly lower, also cannot affect the tension rod, the belt joint two on the platform began to cure. This method is a kind of joint is the best method that can guarantee the high coupling efficiency, but also very stable, joint life is long, easy to master, but the heat curing joint process is relatively complex, high requirements for personnel, cold bonding process is simple and short-term training posts.
Q:The difference between threaded pipe joint and grooved pipe joint
It is divided into: the wire connection and wire connection. If the two are double wire connection is in need of a two double wire transition; if between the two are: double wire connection is in need of a two double wire transition; if the two just one male and one female, and the thread and facilities, it is directly screwed on it is good.
Q:Hydraulic hose joint is spherical and cone sealing, threaded connection, what is the form of joint?
Hydraulic joints are often spherical joints, concave and convex.2 types of teeth with imperial teeth and unf.
Q:What does pipe joint "DD" mean?
Parts that work in a weak corrosive environment, such as covers, bearings, valves, hand wheels, etc., are joined mainly for connection, installation and maintenance.
Q:The gas cooker joint is pagoda shaped. Can it fall down and connect with bellows joint directly?
Only when the thread and the sealing form are the same.The utility model relates to a gas cooker joint, which is an interface for introducing gas into a gas rangeA pagoda shaped joint of a gas cooker is a terminal joint used for connecting a hose to a device. It is only one of the many conversion joints used by the gas interface of the gas appliance to connect to the user's pipe
Q:Specification for thread of gas couplings
3, pneumatic connectors, foreign brands are more well-known SMC, domestic brands are commonly used, SNS, TPM.4, pneumatic joints commonly used series are PCH, PCF, PL, PLF, PB, PD, PX, SL, PH and so on

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range