digital high pressure heat press machineAPD-20
1.factory wholesale OEM ODM
2.high pressure transfer machine
3.heat transfer p
Detailed Product Description
Pneumatic High Pressure Draw-out Heat Press APD-20 New Design is designed with automatic air operated pressing.
Pneumatic High Pressure Draw-out Heat Press APD-20 New Design
Machine Type: Automatic
Platen Size: 16"*20"/16"*24"
Under Plate: Draw-out
Controller: GY-04 Digital Time & Temperature Control
Printable Articales: Up to 20mm Thickness
Air Compressor Required: Yes
Voltage: 120V/ 220V
Time Range: 0-480 sec.
Maximum Temp: 225 C
Temperature Accuracy: ±0.5%
Packing Size: 77*53*75cm
Gross Weight: 62kg(Wooden Package)
- Q:Thermal conductive materials used in electrical and electronic equipment that is the best?
- Seeing you is what equipment, each has his strong point, general or thermal conductive silicone: scientific thermal conductive paste, thermal conductive adhesive, thermal paste is given priority to. Rapid cooling requirements is not high, and want to operate, suggested thermal conductive silicone pads, thermal double-sided tape and kinds of thermal conductive silicone (used to glue need not buckle with cooling products), the cooling requirements high, better thermal conductive silicone.
- Q:Refrigeration equipment of the evaporator
- When refrigeration heating evaporator is hot. Refrigeration is cold, if it is hot is bad.
- Q:What is the working principle of heat pipe
- Typical gravity heat pipe, as shown in the airtight tube first into a vacuum, filling the appropriate working medium under this state, on the lower end of the heat pipe heating, laser vaporization heat absorption for steam, under the small pressure difference, up to the upper heat tube, and gives off heat to the outside world, condenses into liquid. Condensate in under the action of gravity, along the heat pipe wall returns to the heating period, and once again heated vaporization, cycling, continuous heat from one end to the other end. Because is phase change heat transfer, heat pipe heat resistance is very small,
- Q:What are heat exchange equipment
- In the chemical plant, so the heat exchange equipment investment accounted for about 10% ~ 20% of the total investment; In the refinery, accounts for about 35% ~ 35% of total investment. Over the past 20 years, so the heat exchange equipment in energy storage, conversion, recovery, and new energy utilization and has been widely used in pollution control.
- Q:How to wash hot water exchanger heat
- Cleaning method: flush with water cannon directly or join in the heat exchanger cleaning liquid circulation, can take some dirt. The most radical approach is removed all clean. 1, direct circular: hot water to the water heater in loop heat pipe heat transfer directly. 2, the circle of indirect: using in the heat exchanger in water heater, the heat pipe working medium inside the circulating heat exchange. Generally USES the heat exchanger coil structure. The heat exchanger in the process of heating and heat recovery heat, use of heat exchange.
- Q:What are the advantages of rotary kiln raw run on kiln? Please, 3 q
- (1) rotary kiln, rotary kiln combustion equipment and pulverized coal combustion heat therein; As well as heat transfer equipment, raw materials absorb the heat of the gas for calcination. Sometimes other conveying equipment, from raw material feeding end to discharging end. And fuel combustion, heat transfer and the movement of raw materials must be reasonable and collaboration between the three, to make the heat generated by the fuel combustion can in raw material by rotary kiln, rotary kiln in a timely manner to the raw material, has reached the purpose of high-yield, high-quality, low consumption. (2) raw material movement in the particles in the rotary kiln, rotary kiln is more complicated. If the raw material particles on the kiln wall and the raw materials inside the layer without sliding phenomenon, raw material movement is often thought to be like this: raw materials under the action of friction, as a whole with the kiln wall rises slowly, when transferred to a certain height, the raw material layer surface and the horizontal plane Angle is equal to the Angle of the accumulation of raw materials, raw materials particles under the action of gravity, slipped along the bed
- Q:Who know the solar heating of the superconducting technology
- The heating application. Can be used in homes, buildings, shopping malls, factories, plantation, farms, underground heating tunnel. Both the traditional heat pipe radiator, heater, central air conditioning warm air heating is also available. 40 degrees below zero temperature can be adjusted freely, not frozen, energy-saving 50%.
- Q:How hot is spread from one end of the metal strip to the other end of the
- Industry, there are many is given priority to with heat conduction heat transfer process, such as rubber products heat vulcanization, and the heat treatment of steel forgings, etc. In the kiln, heat transfer equipment and the design calculation of heat insulation and the temperature of the catalyst particle distribution analysis, the heat transfer law occupies an important position. In high temperature and high pressure equipment (such as ammonia synthesis tower and the waste heat boiler, etc.) of large-scale ethylene plant design, also need heat transfer law to calculate the equipment temperature distribution of each heat transfer within the partition for thermal stress analysis.
- Q:High heat conduction oil equipment slot can discharge of oil pipeline from oil and gas separator directly below a line
- You said the row tubing is the overflow tube or tubes? Oil and gas separator are system hot oil inside, no matter which is not desirable. Overflow is leads to the low trough, hot oil into the tank is low low trough deterioration of oil product.
- Q:When IGBT coating thermal conductive silicone, how did the general daub the ideal
- The building Lord thermal conductive silicone with machine water can be erased. Times can suggest use silk screen printing, silk screen, scraper hardness 70 with 80 net cloth, Angle of 45 degrees, silk screen material with a PET or NYLON.
As a leading manufacturer, all Microtec products are fully assembled by our state of the art manufacturing facility prior to shipment and released only after extensive testing and inspection by our qualified technicians, maintaining the strictest quality control procedures.Our mission is to be a world supplier of Heat Transfer Products and Consumables. We are committed to the principal of satisfying customer and market demands, pursing scientific administration and superior quality by using the latest technology grounded in a thorough understanding of the end-user's needs.
1. Manufacturer Overview
|Annual Output Value
||7.69% North America
7.69% South America
7.69% Eastern Europe
7.69% Southeast Asia
7.69% Eastern Asia
7.69% Western Europe
7.69% Central America
7.69% Northern Europe
7.69% Southern Europe
7.69% South Asia
||ISO 9001:2008;SGS; CE
2. Manufacturer Certificates
|a) Certification Name
3. Manufacturer Capability
||81% - 90%
|No.of Employees in Trade Department
||5,000-10,000 square meters
|No. of Production Lines
||OEM Service Offered Design Service Offered Buyer Label Offered
|Product Price Range