Q:Integrated ceiling sealing edge role, not surrounded by edge can be?

The edge sealing plays the role of beauty and fixing the buckle plate. It is best not to have much trouble.

Q:Can there be less or no addition of lead stabilizers in the PVC banding? Is there a replacement? Because China's ROHS on lead, chromium, mercury, cadmium content requirements.Is it possible to produce edge banding products that meet the requirements of ROHS? Around Beijing

I am made of raw material; my material does not contain lead; the key is in the raw material

Q:Please advise me. All my predecessors, how can the furniture edge of knowledge, the more detailed the better. Thank you!PVC furniture edge banding in the production of the factory is directly in accordance with the requirements of customer specifications, or first produce a large edge coated paper, processing? How much is the general quantity? And what about a case of boxes?

Edge is a decorative role, is a kind of PVC material, generally has a thickness of 1.0,1.5 two with more than the quality manual, edge durability, appearance is not the machine automatically after all hand edge edge, insufficient force smooth uniform, easy pressure is not formed or not a virtual reality phenomenon. So buy furniture, try to buy machine edge, do not covet cheap!

Q:The main reasons of edge banding degumming

The main reasons are as follows:1, edge degumming is the main processor is too thin especially PVC edgebanding gum (agent) coating is too thin, and the decline of the hot melt adhesive affinity, which is one of the main reasons of the edge degumming.2, is the technical problem of edge machine temperature does not reach the predetermined temperature, causing sticking edge and hot melt adhesive glue is not good, the general requirements of the temperature at 180 ~ 210 degrees, can be adjusted according to the operating environment temperature sealing machine. This is mainly to look at the problem of technicians, manufacturers must strictly check, this is the problem of manufacturers.3, that is, the edge of the machine is too thin glue, originally did not produce a qualified edge banding. This is also an important reason, because the temperature and glue is too thin, causing the phenomenon of degumming is also common, you can increase the amount of glue to solve. The manufacturer's main problem is the manufacturer's responsibility. Everyone wants to think about it.4, uneven plate may also cause banding off, this is also must pay attention to the problem, appear this reason can only explain the installation technical problems.

Q:How to solve the problem of sealing the package door?

Have be close.

Q:How to seal the corner in the half corner of the wardrobe?

Each of these companies is not the same, all can be sealed.

Q:Custom made wardrobe in all friends custom made a wardrobe, a little worried about this edge, how to assess the effect of sheet metal banding?

I think the whole friend's sealing edge is good

Q:My semi-automatic edge sealing machine, the edge is not good, how to adjust?

Look at the temperature. Look at the bite

Q:Panel type furniture automatic edge sealing machine. How many grams of hot melt adhesive does it need per meter?

Generally speaking, the cost of hot melt adhesive for edge banding machine is very small, so few manufacturers will make statistics on it. I checked all the basic data I had about the furniture factory and didn't find it.I asked a friend who was doing hot melt, he said, at about 2 grams. For your reference.

Q:Why does my fully automatic edge sealing machine seal a thick MDF, half of the board has glue, and half does not have the problem of removing the board?

You are common problems, I don't know if you use edge machine what is the specific structure, but it is certain that the plate with the glue vertical axis does not cause, that is to say the transportation guide shaft below the gum is not vertical, processing method depends on the structure of your machine, sealing machine has many with glue pot verticality adjusting device, adjust side pasting shaft and the plate completely consistent, can achieve the purpose of uniform coating; of course there is a glue pot sealing machine is not adjustable angle, if it is not to worry, the gap can be through a bolt mounting hole of the glue pot bracket to adjust the purpose of. There is also a relatively rare reason is that the plastic shaft is not glue, rubber line is always half the height of the plastic shaft, resulting in the top of the board is generally no glue. This situation checks whether there is dirty plastic door, blocking the mouth of gum, or glue temperature on the high side, too fast back glue. In that case, clean up the dirt and lower the glue temperature.