Concentric overhead conducting wire Concentric overhead conducting wire

Ref Price:
Loading Port:
Shanghai
Payment Terms:
TT OR LC
Min Order Qty:
100 m
Supply Capability:
100000 m/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Product properties:

1. The long-term working temperature allowed by overhead conducting wires is 70 oC;  
2. When there are large-span rare weather conditions and there is less ice coating occurring in heavy ice areas, maximum stress the lowest point of the conductor sag should not be more than 60% of instantaneous destructive power;  
3. When the wires are connected, strands around the connecting pipe should not bulge, otherwise the strands of wires in operation will be unevenly stressed, after the joints are pressed, outlets of connecting pipe should be covered with moisture-proof paint to prevent corrosion;
4. When the wires are installed, sag stress of all the wires at the same gear should be the same, and within the range permitted by the limited distances to the ground and exceeding the distance for protection of building, the conducting wire stress can be higher by 10-15% than normal tension.



Scope of application:

This product is applied to overhead power transmission and distribution lines.wires in operation will be unevenly stressed, after the joints are pressed, outlets of connecting pipe should be covered with moisture-proof paint to prevent corrosion;
4. When the wires are installed, sag stress of all the wires at the same gear should be the same, and within the range permitted by the limited distances to the ground and exceeding the distance for protection of building, the conducting wire stress can be higher by 10-15% than normal tension.
applied to overhead power transmission and distribution lines.wires in operation will be unevenly stressed, after the joints are pressed, outlets of connecting pipe should be covered with moisture-proof paint to prevent corrosion;
4. When the wires are installed, sag stress of all the wires at the same gear should be the same, and within the range permitted by the limited distances to the ground and exceeding the distance for protection of building, the conducting wire stress can be higher by 10-15% than normal tension.


Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:question about sub amplifier power cable?
back interior the day whilst audio electronics became into evolving from monophonic sound to stereophonic sound, producers of stereo audio electronics precise the left channel enter for monophonic sound (in case you in elementary terms had one enter) and, if there became into no longer something plugged into the magnificent enter jack, the monophonic sound became into allotted to the two left and precise inputs. on condition that mono is fairly uncommon those days, i don't be conscious of if this continues to be everyday on stereo inputs (which includes powered subwoofers), yet you are able to try it. If it isn't the case (plugging it into the left enter purely is going interior the path of the left amplifier), no count in case you split the sign or no longer is in fact a wash. A subwoofer has 2 voice coils on the motive force, one powered by using the left enter and the different powered by using the magnificent enter. in case you purely have, say, the left enter plugged in, you're in elementary terms using the subwoofer with the left amplifier and voice coil. in case you split it, you're actually using the two voice coils. yet, the split itself cuts the sign point in 0.5. So, you have 0.5 as lots sign enter to each amplifier and the output quantity of the subwoofer heavily is not any distinctive than purely plugging in one enter. one element you are able to desire to do is to get a small, low-value stereo amp or receiver, plug the LFE output into one enter, set the amplifier mode to mono, and run the two line outputs to the subwoofer. that would desire to furnish you 2 complete line point inputs to the subwoofer from the only LFE cable.
Q:1.2 meters below the road can use pvc tube wear armor cable?
Have to fight trumpet, mainly to protect the cable jacket is not scratched
Q:HP Photosmart All-One-Printer C3180 Power cable!?
why don't you e-mail HP see if they will send you a power cord or advise you where to get one in your area
Q:How to join a power cable together?
You can install a plug on the cord to replace the one that was chewed off. Choose one with the same number of prongs as the cord has wires (2 or 3). Be sure to attach each wire to the correct terminal! Splicing the cord is also OK, and tape would not be a problem if applied properly, but I prefer to use heat-shrink tubing. When I do a top-grade splice, I first twist the wires tightly together without making a tail, then I solder them.
Q:Power Cable Adaptor or Distribution Block?
either way is fine unless your total system power will exceed 3000 watts....otherwise it would be cheaper and just as good to just run the 4 all the way from the battery and use the 1/0 gauge for your big three upgrade should you be exceeding 1000 watts
Q:where can i get modular power supply cables?
I've never personally ordered any item specific parts but you should try NCIX . com
Q:if we provide power through power cable will there be need of extra capacitor near load?
Yes, if you are talking about a bypass capacitor. Electronics always requires a bypass capacitor near the circuit/IC. Having one at the end of a cable means the cable inductance is in series, and the impedance seen by the IC power supply leads is inductive and high instead of the needed low impedance that a local bypass cap provides.
Q:Power cables for a CCTV system?
you can buy power cables for a cctv system from global sparenparts private limited.
Q:Does SATA 3.0 and 6.0 use the same power cable?
same interface cable, and same power source cable. YOu just have to make sure the motherboard has a 6.0 gbs slot. I just built a PC with one of these. Not a HUGE improvement, but startup is a few seconds faster.
Q:How do musicians typically transport instrument/power cables?
you can get little velcro ties for like $3 for 50. learn how to coil cables correctly (most pros use under/over) and then secure them with the velcro strip (I like to keep the velcro at the male end of the XLR cables so it's not danglight around on the mike end) and then they should be kept pretty well organized even if you just throw them in a backpack or something

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range