BATHROOM SANITARY WARE ONE PIECE TOILET -8050

Ref Price:
Loading Port:
China main port
Payment Terms:
TT OR LC
Min Order Qty:
100 set
Supply Capability:
2000 set/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Bathroom One Piece Toilet New StyleToilet
1Swing Wash
2Heated Seat(4-level)
3Feminine wash
4Power-saving

 

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:Every time you open the bathroom hot water shower or kitchen hot water faucet can hear from the bathroom
Is because the triangular valve has a problem, open the other faucet when the pipe pressure relief, triangular valve ceramic spool sound
Q:What is the difference between the kitchen and the basin
Stage basin, is the tank installed on the side of the cabinet table, the basin basin basin diameter is greater than the size of the opening of the cabinet countertops, is to put the sink directly on the table, the sink and the seams of the table with glass glue, construction comparison Convenience.
Q:gurgling noise in bathroom sink?
Yep, a venting issue; venting by way of the sink. you ought to deploy a separate vent; one type is a Studor vent. it may deploy adjoining to the laundry standpipe or laundry sink, anyplace it drains. in case you have a standpipe, you will might desire to place in a sanitary Tee and then connect the Studor to it. It in basic terms opens while venting is needed and can splendid the issue. you will get them at any ironmongery shop; lowes, and so on.
Q:bathroom pedestal sink can i wall-mount it with a bracket?
Hello okorder.com/... Hope that helps, Elizabeth
Q:Bathroom sink faucet handle broken?
turn off water underneath the sink - there are two small cutoff valves called stops. Get a lavatory wrench about $8 to access the nuts under the sink.; these make the job easier. Unhook the hot and cold supply lines, usually brass or rubber. Loosen the nuts that hold the faucet assembly to the sink. Disconnect the popup valve (drain stopper) if it has one. Now, lift the faucet off of the sink and you can access the handle to remove. Find replacement handles, but if the faucet is very old and not an antique, just get a new one that fits your sink. Cost ranges from $20.00 to $100 or more, depending on how fancy you want.
Q:What is the maximum size of the basin?
As long as people feel good in which OK ah
Q:Replacing Bathroom Sink Faucet Rubber Seal?
The faucet is held on by 2 flat plastic nuts on the underside of the sink.The area is tight but they are changed every day.I would just buy a new faucet instead of trying to repair the old one as it is not easy to rebuild one and it may still leak after you try to repair it.
Q:how to unglue a bathroom sink from the wall?
ben, bathroom sinks are generally hung to the wall using a metal support bracket. remove any silicone around the sink's perimeter. remove water and drain connections, simply pry sink upward and it shall come off - drywall and or surface texture might come off as well so use care -
Q:Black gunk in bathroom sink?
Your sink is probably OK, just a little dirty The black stuff is soap, grease, hair and whatnot. Go down the hardware and get a plumber's helper which is a thing like a big rubber suction cup on a short handle. Also called a force cup or plunger. See the gizmo with the red rubber cup in the source. Nice and cheap and reusable. Place the cup over the drain and hold it there while you run a little water into the sink - no more than 1 inch (2.5cm) deep. Push the handle up and down until the blockage eases. When it starts to drain, add a little more water and keep doing it. Once the drain is working OK, put in a good shot of laundry detergent and hot water and leave it there a while, overnight would be good but an hour or so is OK, then use the cup again to clear out anything that has loosened. If you use the plunger every now and then the drains will stay pretty well clear.
Q:Decoration how to choose the basin bathroom basin to buy the whole Raiders
In terms of glass basin, Tuoba rabbit Xiaobian suggested that if the economic conditions permit, the best choice of 9mm wall thickness of the product, because it can withstand the relative high temperature of 80 ℃, impact resistance and resistance to damage is also better. As the glass basin from the process to the design costs are higher, so the price is relatively expensive, consumers in the choice of the same product when the shop should be more than three, but the same should consider the strength and credibility of the manufacturers.

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range