Monofilament Machine

Hot Products

CMAX Plastic And Wood Profile And Plate Extrusion Line

Automatic Plastic Pipe Extruding Machine

CMAX Conical Or Parallel Twin-screw Plastic Extruder

PE Plastic Foam Sheet Extrusion Production Machine Line

Conical Or Parallel Twin-screw Plastic Extruder

CMAX High Output Conical Twin-screw Plastic Extruder For High-speed Profiles

PVC Wood-Plastic One Step Extrusion Line

Plastic Extrusion Machine for PE Water Pipes

PP Non-woven Fabrics Plastic Extruder

JSM-Fully Automatic High Speed Thermoforming Machine

FAQ

For example, 70 square conductors, the outer diameter is A, out of the insulation, then the line mouth to choose how much, how much plastic cover election? Then the sheath, then how to choose the mold?

Depending on your specific specifications, if XLPE is insulated, extrusion die with small touch line, set on the use of cable diameter, large core conductor than a few tenths of good, if you like to use 70 square tube extruding mold insulation of the conductor element some is big 1 can be set according to the touch, the tensile ratio calculation,

How to adjust the 65 screw gap in the extruder?

This should be practical learning. The outlet plane of the barrel is about 3 mm in diameter.

Which type of inverter is suitable for extruding machine? Please give expert advice, and G series is discontinued

Proposed Delta VFD-cp Series ~!AskCP2000 is constant pressure water supply... Are you sure you can use it? And C2000 is better than qualifiedChasing the answerWrong number ~ ~ should be C2000, and VE Series ~ ~ these two are suitable, ~~B, CP is not good ~!

Extrusion blow molding machine, storage or continuous type good?

This is not good or bad, depends on what your product is If the product cycle large volume high capacity is bound to produce a product with storage because of your long,

PVC extrusion machine extrusion stone floor no pressure, what reason?

PvC stone floor extruder pressure is adjusted by the screw and die head

What are the components of an extruder?

The driving system of an extruder is to drive the screw, providing the torque and speed required by the screw in the extrusion process, usually consisting of an electric motor, a reducer, and a bearing.3. heating and cooling device for extruderHeating and cooling are necessary conditions for the process of making a plastic extruder. It includes two aspects:(1) now host extruder is usually divided into electric heating, resistance heating and induction heating, heating installed in the fuselage, neck, head of each part. The heating device heats the plastic in the outer barrel to increase the temperature required for the process operation.(2) the cooling device is designed to ensure that the plastic is in the temperature range required by the process. Specifically, to eliminate the excess heat generated by the shear friction of the screw rotation, in order to avoid the temperature is too high, so that plastic decomposition, coke burning or stereotypes difficult. Cylinder cooling water cooling and air cooling is divided into two kinds, small and medium sized extrusion machine adopts air cooling is more appropriate, large use more water or two kinds of combined cooling; cooling water cooling screw mainly adopts the center, the purpose is to increase the solids conveying rate, stable glue volume, and improve product quality; but in the cooling hopper one is, in order to strengthen transport of solid material, prevent warming plastic sticky jam outlet, two is to ensure the normal work of the transmission part.

producing polyethylene polypropylene fiber, masterbatch in the dark spot under the light, that is, masterbatch does not change, filter replacement frequently, half an hour... 40The equipment is Changzhou Riyue extruding machine, production of polyethylene polypropylene masterbatch, a dark spot in the light, it is not frequent replacement of masterbatch, filter plugging, half an hour, I added the 30% filling masterbatch, how to solve this problem? Other particles are not wet either. Masterbatch is not turned for help

This is often called information information, this website. Reference: Fox information Qilu Chemical City PE market by the petrochemical price driven price continues to rise, 7042 no tax 9350-9400 yuan / ton, 02TN26 no tax,

why production is not strong?I have several new co extrusion machines, but the blown plastic bags are not produced by others

Tensile strength is divided between longitudinal and transverse, and PE bags are transversely increased, available 8CLLDPE is added, longitudinal can be added to medium, medium density or high-density material to increase tensile strength.