Z1J-SG-1302 Impact Drill

Ref Price:

Loading Port:: China Main Port

Payment Terms:: TT OR LC

Min Order Qty:: -

Supply Capability:: -

Inquire Now

Add to My Favorites

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

You Might Also Like

Light Hammer Drill DIY and Construction Power Tools

Miter Saw

S1JL Powder Load

Z1J-SG-13 Impact Drill

Z1J-SG-1306 Impact Drill

Z1J-SG-1303 Impact Drill

taper button bit dia34mm,36mm,38mm made in China

Top Hammer taper button bit dia34mm hot selling

Type: Impact Drill Model : Z1J-SG-13
No-load speed : 0-2600 (r / min) hole diameter : 13mm Power Type: AC

Power supply voltage : 220V Rated output power : 800 (W) Rated speed : 0-2600 (r / min)

Technical Parameters
Model : Z1C-SG-13 Order number : 41302
Voltage : 110 / 220V Frequency : 50 / 60Hz chuck diameter : 13mm

Rated speed : 0-2600r / min Rated power : 800W

Standard configuration:
Chassis: Makita Blue + soft + flash silver core height : 40mm copper motor
Cartons 2 m standard cable
Packing Size : 50X40X30 10 units / piece 22KG / 24KG

Q: How big is the screw hole at the back of the torch chuck? Is it a rebound?: Screw head, some cross flower, six angle, etc.. Generally, the thread is covered with a lock gum.If you want to remove it, it should turn clockwise.

Q: An electric drill will be hot for a while: The motor burns,1, with a small motor may be profiteers of high standard big motor, drilling machine overload (smell taste)2, motor iron (see spark)

Q: Can a torch drill against a wall?: In fact, mainly to see the drill bit, drill the strict requirements, only small drill can plug up what. The drill needs an alloy head, otherwise it burns easily.

Q: Hold the electric drill, turn to the right direction, turn the drill down, up, backward, turn left: You take the screws off the handle, and that's where the wires are out of contact

Q: How do I take out an electric drill bit?: Drill bit: with a key, insert the key into the side hole of the drill sleeve and loosen the bit to remove the bit.

Q: How to detect the short circuit of an electric motor stator?: The stator is seldom damaged, and short circuit multimeter measurement is available. Can not be directly connected with the power supply, do not need to change the stator, it only need to rewind coil. Most of the stator injuries are carefully observed and can be found.

Q: Torch drill head leakage: If the stator leakage causes the stator core to live, it will not trip because it is fixed on the insulated plastic case.

Q: Why is the speed of the electric torch slow?: Notice of operation of electric torch:1. Check the power cord before use. If you have, you must wrap up the insulating tape, do not be immersed in the use of water and random drag and tread, and can not touch the heat source and corrosive medium.2, the metal shell of the flashlight must be taken to protect the ground (zero) measures.3. Before use, make sure the torch switch is in turn off, and when the plug is plugged into the power socket, the hand drill suddenly turns.4, electric drill before use should be idle 0.5 ~ 1min, check the drive part is flexible, whether or not abnormal noise, screw, whether loose, the commutator spark is normal.5, drilling, both hands firmly grasp the electric drill, as far as possible not a single hand operation, should grasp the correct operation posture.6, can not use the chipped drill, drill down pressure not too big, to prevent the drill bit interruption.7, cleaning knife head, scrap, change knife first, these actions must be disconnected from the power supply.8, the small workpiece must be clamped with a fixture, and then use a flashlight drill.9, the operation of drilling can not be too large, in case the drill or wire attack, flying wounding.

Q: Can a torch screw a screw?: I just screw it with an ordinary flashlight, where the wrench controls the slow speed. There is a kind of head is the outer six corners, you can clamp it, which sky map for you to see

Q: How do you choose a drill when you want to screw a hole with a torch?: This is a self tapping screw, usually with a diameter of 3 millimeters of drill, but here this screw is not strong, it is best to use the core rivets

Send your message to us

*Email

*TEL

*Quantity

*Unit