Q:What material does the power tool housing fit?

Electric drill: the main specifications are 4, 6, 8, 10, 13, 16, 19, 23, 32, 38, 49mm and so on. The figures refer to the steel whose tensile strength is 390N/mmThe maximum diameter of a drill drilled on a material. For non-ferrous metals, plastics and other materials, the maximum drilling diameter is comparable to the original specifications of 30 to 50%.Electric grinding machine: a tool for grinding with a grinding wheel or millstone. A vertical electric wheel and electric angle grinder.Electric wrench and electric screwdriver: used for loading and unloading threaded fittings. The driving mechanism of the electric wrench is composed of a planetary gear and a ball screw groove impact mechanism. Specifications are M8, M12, M16, M20, M24, M30 and so on. An electric screwdriver adopts a clutch, a transmission mechanism, or a gear drive mechanismThere are M1, M2, M3, M4, M6 and so on.

Q:What's the name of an electric tool for riveting screws into wood? Not understand!

An electric drill can be used! But it can't adjust the torque! There are four types of professional screw twisting tools!

Q:How are the I, II, and III classes of power tools classified?

The popular point is that:The 1 type of tool is metal housing with ground wire.The 2 type of tool is the insulated housing.The 3 type is low voltageOfficial point of explanation can be searched for power tool category ~!

Q:Which is good between pneumatic tools and power tools?

The use of pneumatic tools:1., the air is easy to obtain, and the work pressure is low, the used air can be discharged locally, without the need to recover the pipeline2. gas viscosity is small, flow resistance loss is small, easy to central gas supply and long-distance transportation3. pneumatic actuator, high movement speed4. the pneumatic system has a strong adaptability to the environment. It can work reliably in a wide temperature range, humid and dusty environment, with a slight leakage, no pollution to the environment, no fire and explosion hazards, and safe use5., simple structure, convenient maintenance and low cost6. long life of pneumatic components7. pneumatic actuators of the hydraulic output than small, fast, strong adaptability, can exercise in the flammable, explosive, heavy, damp, the impact of the harsh environment, no environmental pollution, long service life, simple structure, easy maintenance, low price.

Q:What kind of power tools are hand drills? 1, 2 or 3?

I class: in the prevention of electric shock protection, in addition to relying on basic insulation, but also the need for zero protection.Class II: the tool itself has double insulation or insulation without the need to protect the ground.Class III: Powered by a secure, ultra low voltage power supply, no voltage higher than the safety supply voltage is generated within the tool.The above is the classification of insulation categories.

Q:What devices must be available for all hand held electric tools?

Hand held electric tools, insulation measures are in good condition, must be equipped with qualified leakage protection device, forbid to change the power cord and plug, use special flow switch box.

Q:What safety problems should we pay attention to when using electric drills or hand-held power tools?

All of the wires must be more tough and durable rubber covered wire. When the wire enters the shell of the motor, the rubber ring is used to protect the insulation layer of the wire from being worn out.

Q:Is the motor of an electric tool the alternating current motor or the direct current motor?

The series motor is usually used. The series motor is connected in series because the stator and rotor windings are connected together, so when the current is reversed, the magnetic field is reversed, so the torque direction remains the same. However, according to this principle, the motor works at 180 degrees after the torque is gone, so even the AC motor, but also need to reverse, in order to work like a DC motor.The rectifier also needs to be rectified if it is operated under the direct current. The rectifier bridge is very small. On the circuit board, there are four diodes close together, mostly rectifier bridge

Q:What is the working principle of power tools?

AC motor, AC motor of induction motor, its strong induction current (eddy current) magnetic field generated in the rotation of the magnetic force on the rotor copper bar, continuous cutting, according to Lenz's law, the induced current has the effect of relative motion occurs against the rotor magnetic field and the rotor is, with the magnetic field and rotation. But the rotor rotation speed of the high speed magnetic field does not transform, otherwise it will not be able to cut the copper lines.

Q:Power tools are power tools?

General refers to power tools, and in some cases pneumatic tools are used.