Q:On that platform, you can buy thermostatic shower valve body

Is the spool bar? Spool is not sold alone, are bibcock, gate valve sales. I hope my answer can help you

Q:What does "200" mean on valve h14w?

Work stress 200psi. PSIPounds per square inch. P refers to the pound pound, S refers to square square, I refers to the inch inch, into a metric unit: 1bar = 14.5psi

Q:Valve body WCB tolerance, low temperature

WCB is cast carbon steel, and WCB forgings are A105. The valve is written to indicate the material of the valve body.The United States is the WCB grade, equivalent to the domestic ZG250-485 (ZG45), the chemical: C = 0.50; Si = 0.60; Mn = 0.90; P = 0.040; S = 0.040; Cr = 0.35; Mo = 0.20; V = 0.05; Ni = 0.30; Cu = 0.30Suitable temperature range from -29 to 425 centigrade.

Q:The transmission valve is out of order. Could it cause manual gear to prevent the automatic block?

Increase friction and wear, while sludge will also be in the transmission box, resulting in the valve and pipe blocked, can not be achieved in order to adjust the oil pressure, resulting in transmission failure problems.

Q:Ordinary butterfly valve body material arrangement order.

2 FCMB for working temperature between - 15 ~ 300 DEG C, nominal pressure PN is less than or equal to 2.5MPa in the low pressure valve. Applicable medium is water, sea water, gas, ammonia and so on.3 ductile cast iron ductile iron is a kind of cast iron, the cast iron, nodular or spherical graphite instead of flake graphite in gray cast iron. This change in the internal structure of the metal makes its mechanical properties better than ordinary gray iron, and does not harm other properties. Therefore, the valves made of ductile iron use more pressure than those made of gray iron. Suitable for working temperature between - 30 ~ 350 DEG C, nominal pressure PN is less than or equal to 4.0MPa in the low pressure valve.Applicable medium is water, sea water, steam, air, gas, oil and so on.

Q:How to break the electric head and body of the electric butterfly valve?

The electric head and valve are connected normally. They need to be connected by screws, nuts and gaskets. They can be removed when all the screws are removed.

Q:Is the valve in the car gearbox hydraulic?

The speed at which the fluid flows out of the turbine V can be seen as the rate at which the work fluid flows out relative to the surface of the turbine blade, and is combined with a rotational velocity U of the turbine. When the turbine speed is relatively small, the working fluid flowing out of the turbine is backward, and the working fluid impacts the front of the guide wheel blade. Because the guide wheel is limited by a one-way clutch, it can not rotate backward, so the guide vane moves the working fluid backward to guide the impeller of the pump wheel to promote the rotation of the pump wheel, thereby increasing the torque acting on the turbine. As the turbine speed increases, the rate of u increases as the speed V of the Omega and u begins to point to the back of the guide vanes. The torque converter reaches the critical point. When the turbine speed increases further, the working fluid will impact the back of the guide wheel blade. Because the unidirectional clutch allows the guide wheel to rotate forward with the pump wheel, the guide wheel rotates freely along the rotation direction of the pump wheel under the driving of the working fluid, and the working fluid flows back to the pump wheel smoothly. When the working fluid outflow from the turbine guide vane outlet coincides with the same direction, the torque converter is not produced by twisting effect (the torque converter condition called hydraulic coupling condition).

Q:Does the Buick GL8 transmission not have any relationship between the jump gear and the valve body?

Whether the main oil pressure is too low, the control shift oil pressure is too low, the internal clutch in the transmission box, the brake is not too large clearance, excessive wear, gear switch whether the signal error, the computer version is a problem

Q:Speed box valve above the solenoid valve generally has several points, what functions and role?

Basically 5-8, each stall with different stalls and oil pressure. It's an electrical signal, it doesn't have any special function!

Q:Our company produces valve material is ADC12, there is a large number of cracks on the valve body, what is the reason for the material is bad or there are other reasons?

That's why so many,1, alloy iron content is too high or silicon content is too low2, the content of harmful impurities in the alloy is too high, which reduces the plasticity of the alloy