Q:Heating valve above in addition to a scale of plastic, looking at a corner valve, and if disturbed in the wall, that is, a through valve, so this device with ordinary angle valve or through valve can replace it?

This valve is generally plunger valve, and angle valve is mostly ceramic valve, which has a rubber cushion is bad

Q:Do you need angle valves for gas water heaters?

Unwanted。There is no need to use angle valve when installing sprinkler:Install a shower, usually with your hands, because the shower itself has a plastic pad, not much effort can be twisted tight, and no leakage. Because the sprinkler is the sprinkler end, the pressure itself will not be concentrated in the shower connector, so no professional angle valve on it.Generally speaking, the shower is connected to the back of the hot and cold water valve, what kind of temperature, and adjust the proportion of hot water and cold water. Unless the hot and cold water valve is broken, the water can not be shut, and the current is plus an angle valve

Q:a little ring, but also smell a bit of gas, but a little better, what's the matter?

First of all, make sure the pipe is connected and there is no leakage. Safety is the first.Then again speak loud, the gas jar jetted from the jar, there will be a natural sound, and because the valve opening is opened slowly, so a gas flow speed, so the noise will be relatively large. When the gas is filled with the pipe, it does not continue to use. The air pressure in the pipeline rises. At last, the gas pressure is no longer flowing out of the tank, so there is no noise.As for the smell of gas, how much should be a little leaked, but the taste is great, or persistent, that is the pipeline problems, and quickly close the valve to check.

Q:How do I change the angle valve?

Inlet angle valve should first spin off valve, flange valve on the screw angle, the angle valve and electric water heater from then unscrew water from a new angle valve, angle valve according to the steps to install it, the hot water outlet valve close the inlet can be replaced as long as the angle.

Q:The thread of the angle valve is broken in the water pipe of the wall and wall. What shall I do?

You can cut it off with a flat headed screwdriver or a small chopper, and slowly turn it out

Q:Angle valve removal and installation

.Installation steps of single hole water tap:Step 1: remove all copper fixed base.Step two: screw the nut counterclockwise from the threaded pipe.Step three: hose, wear yellow spanner, nut, threaded pipe, silicone pad.Step four: cross the hose through the containers to be installed (sinks, basins, etc.) pay attention to: silicone pad in the vessel installation at both sides of each piece, and finally tighten, can be fixed more stable.Step five: the small end of the hose is screwed into the faucet inlet by hand and screwed until it is screwed. It does not need to be screwed by other tools.Step six: screw the threaded tube into the lower side of the faucet. The silicone pad on the side of the vessel can be placed under the faucet.Step seven: nut fixing faucet, screw nut can be tightened, installation completed.

Q:So the electric water heater doesn't keep under pressure. Is it possible to install the valve? 40

The risk of pressure in the water heater line is far from the danger of dry fire. If the dry - burning device fails or the heating of the heating element is dried by mistake, the heating element will be burned at most one or two minutes. Therefore, the installation of imported control angle valve is prohibited. But if the water pressure is too high, install the pressure reducing valve (regulating valve).

Q:How about the Moen angle valve?

Moen is the brand goods, angle valve is certainly not bad, good angle valve, in the hand of the heavy work, especially fine, the surface is particularly bright, no scratches, good stuff and bad things, two compare, You'll see. the good that is not good

Q:Ball core large flow angle valve why the noise of water flow?

Angle valve in accordance with the spool form, the valve core for the ball, can also be classified as a ball valve

Q:The angle valve is wrapped with several circles of raw material

When the 5 screw thread not to death by a twist, strong points, not necessarily is screwed to the screw does not move until no leakage, as long as the twist when you can feel anything to eat. Also note that the twist in the depth of two feet, such as cold and hot water mixing valve on the wire, twist when we must pay attention to keep a wall from the agreement, especially in the wall two faucet elbow inconsistent case depth,I say one more thing, not necessarily to the outlet valve angle upward, according to the actual situation, such as the length of the hose to hose, natural bending direction, such as hose longer, can make the angle valve outlet inclined downward, the hose drooping naturally after the lift, to avoid long-term stress caused accidents hose.