Q:Will the aluminum doors and windows 11.2mm and 1.4mm how to identify? Profile 828,888,757,898, what does that mean? What is the thickness requirement?

There is no way to identify, it is impossible to remove the amount of the general are not enough!

Q:What should the inspection of the glass door? The door frame is the metal door frame is also our installation, it should use what inspection batch?

In the "construction construction quality acceptance of a unified standard" GB50300-2001 Appendix B construction engineering division project, sub-project division which is not installed inside the glass doors and windows are doors and windows installed, which is different. Suggestions are still done as required. According to the special door to install the project to do the inspection batch.

Q:Aluminum alloy doors and windows corner code used in doors and windows where the position

Mainly used for aluminum alloy profiles and profiles on the connection

Q:Aluminum doors and windows are fire

If the middle of the PA66 nylon, then the melting point will be higher, PVC directly to die

Q:Aluminum doors and windows of the three windows and doors is the three anti-

Anti-theft This is the basic function of the door, the door can be tamper, the use of general hand tools, 15 minutes can not pry open. Door locks can be anti-drilling, there is a certain scientific and technological content. Fire protection The door is made of metal, in the fire, a certain period of time, to prevent the fire and smoke spread, to prevent the spread of fire. Anti - noise Door body insulation material, cold and anti-noise, install the three anti-door, you can no longer install ordinary doors.

Q:i have a metal (aluminum) door - very thin sheet on each side and then it has a styrofoam like insulation in the inside. well, the people who lived her before cut a hole in it about 6 inches high 4-5 inches wide... my guess is for a pet of some kind. anyway, when i moved in it was covered with tape and filled with wall insulation. i want to fix it it doesnt have to be perfect by any means- its not even an exit door i use i just want it to stop letting cold and hot air in and out....my idea was something involving that spray can insulation.... but if i have tape on the one side while spraying that in im afraid itll leak..... any suggestions?

just get some sheet metal and some rivets to patch the holes

Q:If so, what is the best way to do that? What is the best type of paint to use on metal doors?

Not necessary to remove the old. Just use a Liquid sandpaper to clean it well. Available at all paint suppliers. Manually sand any bare or rust spots, (although may be aluminum), and use a metal base coat. There are many paints for metal. Check with your supplier.

Q:its a double car garage, windows across the top. When we had it installed we didnt opt for the extra money to get an insulated one and boy are we sorry. Our previous garage door was wood, which never got hot to the touch so we had no idea how hot a metal one would get - the heat that thing radiates is incredible and its not even in direct sun

I just bought 2 Styrofoam insulation, cut it to size with an electric carving knife and glued it directly onto the door panels with Liquid Nails. You do have to allow a little tolerance where the joints bend as the door goes up. I put the panels on first, then carved off a 45 degree slice off every panel at each joint. BTW, painting the door bright white on the outside will make an amazing difference as well.

Q:they seem to pop and creak in the morning when the sun starts hitting them. It's very annoying when we're trying to sleep. Has anyone had this problem or know of a solution?

The good thing is that they are doing what they are designed to do. It sounds like these doors face east and get the early morning sun, meaning that they go from cool exterior side to instant sun and heat, while still being cold on interior. The doors are sealed properly and they are just moving like they are designed.

Q:Aluminum doors and windows how to dismantle

The window design of the aluminum alloy window is the groove below the deep groove below, you need to hold up the screen up, and then you will see the gap below. In actual use, the aluminum window will change with time, so try to rely on both sides of the demolition, because the middle position is not easy to support the window beam collapse.