Overhead Sectional Garage Door

Ref Price:
Loading Port:
China Main Port
Payment Terms:
TT OR LC
Min Order Qty:
-
Supply Capability:
-

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

1.Each section panel's joint is adopt "Finger-protection"(Pinch-resistant) safety Design in order to avoid any finger injury when door open and close. The panel  is injected with polyurethane foam(CFC FREE). Foam density is 40kg/m3 All the panels are produced by continued production line which provide the stable quality.

2. Special design of pinch-resistant, there is continued folding part along the panel,thus the panel can be cut at any size,the hinges can be installed accurately and firmly.

3. Wood-grain or stucco Texture surface increases intensity and gives better appearance

4. Thickness of the panel:40mm with the 0.326mm,0.40mm and 0.45mm

5. Max.width of the panel:11800mm

6. Section height: any size between 44-55cm

7 .40mm panel heat consumption factor:K=1.0W/m2k  Heat  consumption factor of the installed door:K=1.6W/m2k

8. standard and special colors for the selection

9. patterns for choice : blocks,stripes,H-line,smooth

a, unique transparent, elegant anodized aluminum frame

b, thickness: polycarbonate thickness between 3mm to 9mm,tempered glass,mirror glass,single or dual pane are available

c, UV proof

d, impact-resistant and burglar-retardant

e, resistance to wind load :Class 3   Water-tightness:Class 3   air permeability:Class 2  

f,  more options are available: combination of materials in polyurethane and polycarbonate with  the anodized aluminum frame,highly robust and durable hardwares

g, all the sections can be replaced easily

h, 200 times harder than normal glass, the door resist the impact of external force and will not easily be damaged,even under the harsh environment the door will not easily become deformed owing to corrosion

i, an effect of day-lighting, firm and smooth and could be used for a long time without maintenance

j, It is applicable to various modern, simple and fashionable architectural styles, such as commercial shops, chain-stores etc.

k, lift way: standard overhead,high lift,vertical lift

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:Can I use oil based stain on a primed metal door with vinyl trim?
start removing it with a thinner or stripper. try a thinner first, as it might be a tidier removal. you need use a paint intended for metal surfaces. some might suggest the right primer would work but i wouldn't even bother. just use a paint for metal surfaces. stains will only work on porous surfaces.
Q:Titanium magnesium alloy door and solid wood composite door which expensive
Kitchen with solid wood composite doors Bathroom is best choice for titanium and magnesium alloy is not afraid of water Titanium magnesium alloy door waterproof moisture is not deformed do not fade glass are also tempered glass solid wood composite door to more expensive
Q:How to remove vinyl letters from painted metal door?
I just repainted a metal door, and removed the paint with a paint scraper and a blow dryer. I'm thinking this will work with your vinyl letters. A heat gun would probably be a little faster than a blow dryer if you have one available. It was time consuming, but it worked.
Q:Repair small hole in metal front door?
small place on metal door, use some JB Weld follow directions an cover hole, prime and paint. Small hole in wood door use wood putty fill hole,smooth over prime and paint.
Q:How do you repaint a metal garage door?
Ok. It was not painted properly the first time. For if it was, the paint would stick as well as your paint job on your car.(and that handles 100 mph speeds without a problem, right?) So you got to prep the door -which basically means getting rid of all the loose paint. If that is the whole door then so be it. Use paint stripper (I like Circa brand) and brush it on. It is thin like water, but bites into that paint and shrivels it up (read instructions on can) Use a natural bristle brush for nylon or polyester will melt. This works on oil based paint only. If the door is painted in latex, it is sandpaper and scraper knife methodology. You must rid yourself of that top coat of questionable paint, because you do not know the reason why it is peeling. So, we do again. Generally all garage doors come with a coat of primer on them(usually grey) Try to leave that coat on and not to sand down to metal if you can avoid it. If your door is bare metal underneath, it would be good for you to know what metal. So ask the dealer to see if it is steel or aluminum. Different primer/undercoats are required. Does not hurt to go to an autobody supply shop and see what they have for paints. They will set you up proper. Remember, clean, clean, clean(no wax, oil, silicone,dirt, dust or anything you can think of should not be on the door before you start to do the job.
Q:how much it will cost to to cut a sheetrock wall and install a metal door?
You forgot about replacing the drywall, taping, mudding, and painting. Depending on how big the wall is that will need to be painted, you could be looking at up to $1000 in labor. It depends on what your labor rate is in your area. The changeover can be done in about 5-6 hours, but the finish work takes awhile. Hope this helps.
Q:Plastic steel doors and windows and aluminum alloy doors and windows with what materials to fill, why?
After the installation of doors and windows should be filled with two foaming agent can play two roles 1 waterproof 2 shock (the main or shock friends because of a long time the foam will aging into a powder) the general project is foam again after the cement Cement and the external walls of paint and then hit a good weathering glue if you are a private decoration, then make a plastic after the bubble (glass glue can also be friends) can be the premise that the gap is not a big case of private and engineering Compared to the project after all, it is a hundred years
Q:Kitchen aluminum door deformation how to repair their own
Do not have to find someone else to change it hee hee
Q:how to put wood on a metal garage door?
Sure you can. Depending upon the condition of the paint on the door now, you may simply be able to wash and paint it without other prep. Use a high quality paint intended for metal surfaces like Iron Clad. Any paint store can help you pick a suitable paint. Benjamin Moore, Sherwin Williams, ICI, ZInnser- they all have paints specifically for metal. Back to prep work though. If the paint is peeling on the door, you will need to sand or scrape it off until you get to a surface that is free of peeling paint. This is usually a full weekend job... Good luck.
Q:0.8 thickness of aluminum doors and windows how much money a square meter
I want to ask you next! Is your own home or plant with it! But I still advise you not to use the wall thickness is too thin 868 type 0.8 almost as much as 130 or add a little money to do a little bit of it

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range