Solar System Water Pump For Agricultural Farm

Ref Price:
Loading Port:
China Main Port
Payment Terms:
TT OR LC
Min Order Qty:
-
Supply Capability:
-

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Specifications

1.wide working voltage:38-96v
2.can be directly connected to solar panel
3.built-in MPPT,can make the best use of solar energy

  • Pressure:High Pressure

  • Application:Submersible

  • max flow:20T/H

  • max head:20m

  • voltage:48v

  • power:1440w

  • intake:140mm

  • outlet:62mm

  • By CE Certification

  • DC input, wide voltage(working voltage:38V-96V)

  • Built-in MPPT which can make the best use of the solar energy.

  • The pump can be directly connected to solar panels in sunshine without controller.

  • The pump include Over-voltage protection / Under-voltage protection / Over-current protection / Over-load protection.

  • Environmental protection, achieve zero carbon dioxide emissions.

  • Solved the water shortage problems of the area without electricity

  • Tank/Cistern filling

  • Village or family water supply

  • Water supply for farm

  • Garden/courtyard irrigation systems

  • Livestock watering

  • Swimming pool filling

  • Fountains

  • Water supply for bivouac or camping car

  • Solar water circulating system

  • Renewable energy projects

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:What is the difference between centrifugal pump and positive displacement pump?
The centrifugal pump is to rely on high-speed rotation of the impeller to do work on the fluid. These two types of pumps are also the most widely used.
Q:Because the water pressure of the booster pump is not enough, it can not work automatically. It can only be operated by hand. It is inconvenient to use.
The worst case is that the pump is not automatic when it leaves the factory, and no one can say whose product is 100%.But there may be automatic control of this piece, not debugging (this depends on the specific product manual or manufacturer)
Q:Why is the submersible pump tripped on an electrical switch?
Calculate or refer to the water pump nameplate that the normal operating current, according to this data exchange switch.2) with 500V shaking table, measuring the cable, motor insulation is in line with the requirements
Q:What should be used to pay attention to the use of mechanical pumps?
Overall: large pump should first do a good job of the foundation, to find a good whole, fixed, and motor, pump should be added good oil, the first test of the motor, and then conjoined test
Q:What is the difference between swashplate pump and crankshaft pump?
In hydraulic system:Axial piston pump is the use of parallel with the transmission shaft in the plunger plunger reciprocating movement of the volume changes generated by the work. As the plunger and the plunger hole are circular parts, processing can achieve high accuracy with the high volume efficiency, stable operation, good flow uniformity, low noise, high working pressure, but the hydraulic oil pollution is more sensitive, more complicated structure, high cost.
Q:Is the flow meter in front of the pump or after the pump?
Agree upstairs. Pump should be straight before the paragraph, 15 times the nominal length of the caliber.
Q:What are the ways of hydraulic pumps?
There are several ways:Direct flow mode, such as external gear pump;Port plate, such as vane pump, axial piston pump, etc.;
Q:How to maintain and repair the booster pump of pipeline pump?
Two 、 troubleshootingfaultReasonRemoval method1. water pump does not produce waterThe water injected into the water pump is not enough, the rotation direction is not right, and the impeller passage is blocked.Pump water into the pump, pass through the impeller runner, adjust the direction of rotation.2. pump flow is insufficientThe pump speed is too low, part of the blockage, the total lift pump is higher than the rated value, the damage to the impeller.Clean the water pump and pipe, replace the impeller, increase the pump shaft revolutions, adjust the outlet valve.3. lack of outlet pressureThere is air in the liquid, the speed is too low, the impeller is damaged and the outlet valve is open.Exclude liquid air, increase the pump speed, replace the impeller, adjust the small outlet valve.
Q:How long does the fine stone pump need maintenance? What should I pay attention to?
Check the line from the relief valve to the cylinder inlet to ensure that there is no external drainage or deformation due to impact and wear and that the connections are complete and fully tightened. - replace any damaged pipe immediately. - change the original settings strictly: all adjustments and calibrations can only be done by professionals. - no fucks hydraulic components, otherwise manufacturers on product warranties and liability shall not be responsible for. A warning because the hydraulic oil can reach very high temperature, there is the danger of burns, so open pipe fittings should take appropriate protective measures. Any replacement parts must conform to the level specified by the manufacturer. 8.2 check lubrication grease pump in oil at any time to ensure adequate and clean the lubrication pipeline joints without overflow phenomenon. Check the lubrication of the running parts at any time, and find the parts which lack oil, and check them immediately to prevent accidents. - check that the centralized lubrication system is effective daily. When the grease pump is empty, the grease added is often not easy to pump out because of the bubble. In this case, open the outlet of the pump, run the grease pump until the grease is re flowing, and then connect the pipe
Q:What are the uses and precautions of magnetic pumps?
2, when the suction surface above the pump axis, before starting the valve can open the suction pipe, if the aspiration level below the pump axis, the pipeline to be equipped with bottom valve;3, the pump should be checked before use, the motor blade rotation to be flexible, no jam, no abnormal sound, the fasteners should be tightened;4 、 check whether the motor rotation direction is consistent with the magnetic pump steering mark;

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range