PVC skinning foam board extrusion line
1.Raw material:PP/PE/PVC(can use recycled plastic)+wood/rice husk powder
2.Final product: decking, garden railing, garden furniture, wall cladding, pallet, garden deck.
window and door,furniture board, ceilling panel, wall siding panel, flooring, partition wall.
3. PVC skinning foam board extrusion line final products:
PVC foam plate/sheet/board, PVC expansion sheet/board/plate
4. PVC skinning foam board extrusion line products properties and application:
WPC foam board machine/PVC WPC foam board machine brief introduction
The PVC foam board is made through foaming and pressing into shape with additive. It is widely used in sanitaryware, construction material and advertising material.
PVC foam board has its properties of easily sawed, bonded, nailed, joint and hot moulding.
PVC crust/skinning foam plate/sheet/board properties
2.Fire retardant and self-extinguishing.
5.Anticorrosion and antitoxic
6.Tough, rigid with the high impact strength
7.Stable color retention
PVC crust/skinning foam plate/sheet/board applications
1.Building outdoor wall board, indoor decoration board, partition board in office and house
2.Screen printing, flat solvent printing, engraving, billboard and exhibition display
3.Chemical anticorrosion project, special cold project, environmental protection
PVC crust/skinning foam plate/sheet/board specifications
1.Thickness (mm): 1 – 25mm
2.Width (mm): 1220, 1560, 2050
3.Length (mm): 2440, 3050, 6000
4.Density: from 0.5 to 0.8
5.Color: white, black, red, blue, yellow, green, gray
5. PVC skinning foam board extrusion line main constitute:
Conical double screw extruder
Conical double screw co-extruder
6. PVC skinning foam board extrusion line main technical parameter:
Main extruder and motor
Conical double screw extruder 75kw
Co-extruder and motor
Conical double screw extruder 37kw
Multi-roller haul-off machine
7.Main technical information of PVC skinning foam board extrusion line
Profile Max Width
Vacuum Table Length
- Q:Wire 70 extrusion machine before and after the transfer of the core will change what is the reason?
- The nose is not accurate enough or wornOr the screws are not screwed in placeOr die inappropriate, too large
- Q:How to choose the mould of the cable extruder? Ten
- Depending on your specific specifications, if XLPE is insulated, extrusion die with small touch line, set on the use of cable diameter, large core conductor than a few tenths of good, if you like to use 70 square tube extruding mold insulation of the conductor element some is big 1 can be set according to the touch, the tensile ratio calculation, PVC1.6 DYWL material with smaller good-looking it is simple of the extrusion process
- Q:Computer case shell plastic is injection molding or extrusion molding?
- 1. injection molding2., the structure is relatively complex, high appearance requirements. Extrusion does not meet requirements3. most are: ABS, ABS+PC, PP and so on4., according to color requirements granulation - drying particles - filling the mold ---- debugging injection molding machine ---- injection molding production - after the selection of finished packaging (if silk screen requirements, but also the need for silk screen)
- Q:Comparison of injection molding machines and Extruders
- The plastic to replace steel or nonferrous metal, plastic cement, which is widely used in agriculture, building materials, packaging, machinery, electronics, automobiles, household appliances, petrochemical and defense, extruder and daily life other fields. So it can be predicted that in twenty-first Century, the plastic will be one of the most important raw material of human activities. The extruder design due to extrusion molding is the main form of plastic processing, so the development of plastic extrusion molding technology and equipment has important significance. The polymer materials used in blending type mixing equipment modification there are three main types: parallelwith twin-screw extruder, reciprocating screw kneader and series disc extruder. The small corotating twin screw extruder has domestic production can squeeze But tons of large mixing extrusion granulation unit will rely on the import machine technology. At the same time. Reciprocating screw kneader and series disc extruder is a necessary device for preparing high fill and high added value of polymer alloy, the current domestic research on them is just in the prototype stage, specifications, varieties not all, have broad prospects for development.
- Q:PVC extrusion machine extrusion stone floor no pressure, what reason?
- PvC stone floor extruder pressure is adjusted by the screw and die head
- Q:Cable extruder how to match the mold, how to calculate the formula, ask the master pointing
- Look at what you have in the form of mold, extrusion, drawing, or half pipe
- Q:What are the components of an extruder?
- The driving system of an extruder is to drive the screw, providing the torque and speed required by the screw in the extrusion process, usually consisting of an electric motor, a reducer, and a bearing.3. heating and cooling device for extruderHeating and cooling are necessary conditions for the process of making a plastic extruder. It includes two aspects:(1) now host extruder is usually divided into electric heating, resistance heating and induction heating, heating installed in the fuselage, neck, head of each part. The heating device heats the plastic in the outer barrel to increase the temperature required for the process operation.(2) the cooling device is designed to ensure that the plastic is in the temperature range required by the process. Specifically, to eliminate the excess heat generated by the shear friction of the screw rotation, in order to avoid the temperature is too high, so that plastic decomposition, coke burning or stereotypes difficult. Cylinder cooling water cooling and air cooling is divided into two kinds, small and medium sized extrusion machine adopts air cooling is more appropriate, large use more water or two kinds of combined cooling; cooling water cooling screw mainly adopts the center, the purpose is to increase the solids conveying rate, stable glue volume, and improve product quality; but in the cooling hopper one is, in order to strengthen transport of solid material, prevent warming plastic sticky jam outlet, two is to ensure the normal work of the transmission part.
- Q:Which converter is suitable for extrusion machine 5
- Proposed Delta VFD-cp Series ~!AskCP2000 is constant pressure water supply... Are you sure you can use it? And C2000 is better than qualifiedChasing the answerWrong number ~ ~ should be C2000, and VE Series ~ ~ these two are suitable, ~~B, CP is not good ~!
- Q:PLC based extrusion machine control system design graduation thesis and PLC based injection molding machine control system graduate 20
- Tip two: choose topics based on your interests. The title selection and refining skills of the two, is from the author's hobbies and interests, only conform to the topics and interests, the author accumulated data can work normally, language applications can also Practice makes perfect.
- Q:How many roots are produced in an hour for an PVC tube extruder?
- It depends on the type of your extruder and the specification of the tube you produced
1. Manufacturer Overview
|Annual Output Value
2. Manufacturer Certificates
|a) Certification Name
3. Manufacturer Capability
|No.of Employees in Trade Department
|No. of Production Lines
|Product Price Range