pvc foam sheet production line/wpc foaming board extrusion line/plastic machinery

Ref Price:
Loading Port:
Payment Terms:
Min Order Qty:
1 set
Supply Capability:
10 set/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

 pvc foam sheet production line/wpc foaming board extrusion line/plastic machinery


PVC,EVA,PE Waterproof  Sheet Production Line


Mainly used for producing PVC,EVA,PE waterproof sheet,it is used for house waterproof in industry and architecture,and basement,architecture waterproof project in reservoir,dam,road tunnel,railway tunnel,bomb shelter,grain depot,refuse dump,waste water disposal,etc.



TPO Waterproof Sheet  Production Line

Far East Machinery Company adopts the solid roll for cobinging multilayers,this new technology make the TPO sheet having a good function against wind uncovering.TPO waterproof sheet is a new type of waterproof product,which was produced with thermoplastic polyolefin plus antioxygen and plastifier and so on,the middle layer is polyester fabric for reinforcement,the surface is laminated with textile fiber and alunimun foil.This kind of TPO waterproof sheet has the features of good weatherproof and suppleness.It is mainly used for house,tunnel,basement architecture and other waterproof fields.


PVC Floor Leather Production Line

Mainly used for producing the sort of PVC floor leather.It has the performance of anti-friction,corrosion resistance,skidproof,impermeable and inflaming retarding,is widely used in auto,hotel,amusement place,exhibition hall,house,etc.


Main technical specifications


Product structurePVC+net+PVCTPO+Net+TPO
Product width2200mm3200mm
Product thickness0.5-3mm0.8-3mm
Designed capacity1000kg/h1200kg/h

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:Produce 10 square wires with the smallest extruder
If the production of single core line, then 50 machines can also do, but low efficiency, unstable line,.70 or 90 machine ideal
Q:Extrusion blow molding machine, storage or continuous type good?
The amount of extrusion must be continuous, efficient, and wasteful
Q:Comparison of injection molding machines and Extruders
Considerations for extruder use:1, extrusion machine is running forward, avoid reverse2, avoid fasting operation, must heat engine feeding operation, so that can avoid sticking bar (holding shaft) phenomenon3, the extruder inlet, vent hole is strictly prohibited access to iron and other miscellaneous, so as not to cause accidents, affect production4, safe use of electricity, grounding wire5. When the machine is running, it is forbidden to touch the rotating parts such as the material inlet, the material outlet, the belt, the gear and so on6, before using the machine should be injected with lubricating oil, so as not to cause damage to the machineSince the extruder as one of the three synthetic plastic material since the advent of rapid development.
Q:Where is the Huangyan extruder machine?
You want to see what type of mold processing, but Masino comprehensive, injection mold, blow mold, mold and so on can be developed.
Q:What is the temperature setting of the extruder and how much is the setting temperature of the head and filter?,
Setting the temperature completely depends on the actual situation.Generally, the position of the leaky hopper is lower than the temperature of the extruder barrel and the die head
Q:Basic parameters of extruder screw
3, compression ratio epsilon, also known as the geometric compression ratio of screw, is the ratio of the volume of the first screw groove to the volume of the last screw groove at the homogenization section. It is determined by the physical compression ratio of plastics - that is, the density of the product and the density of the performance of the feed. The extruder is relatively compressed, the purpose is to make granular plastics fully plasticized and compacted. The selection of compression ratio should be different when different kinds of processing plastics are used. According to the compression ratio, the types of screw can be divided into three types: equidistant, unequal depth, equal depth, unequal distance, unequal depth, unequal distance. Among them, equidistant and unequal depth is the most common one. This kind of screw is easy to process, the contact area of plastic and cylinder is large, and the effect of heat transfer is good.
Q:Is the extruder the same as the extruder?
The extruder is also called in the screw extruder is under the action of the molten plastic extrusion through fixed shape extrusion, water cooling after cutting in the traction machine under the same section is mainly used for a variety of products.
Q:What are the components of an extruder?
The driving system of an extruder is to drive the screw, providing the torque and speed required by the screw in the extrusion process, usually consisting of an electric motor, a reducer, and a bearing.3. heating and cooling device for extruderHeating and cooling are necessary conditions for the process of making a plastic extruder. It includes two aspects:(1) now host extruder is usually divided into electric heating, resistance heating and induction heating, heating installed in the fuselage, neck, head of each part. The heating device heats the plastic in the outer barrel to increase the temperature required for the process operation.(2) the cooling device is designed to ensure that the plastic is in the temperature range required by the process. Specifically, to eliminate the excess heat generated by the shear friction of the screw rotation, in order to avoid the temperature is too high, so that plastic decomposition, coke burning or stereotypes difficult. Cylinder cooling water cooling and air cooling is divided into two kinds, small and medium sized extrusion machine adopts air cooling is more appropriate, large use more water or two kinds of combined cooling; cooling water cooling screw mainly adopts the center, the purpose is to increase the solids conveying rate, stable glue volume, and improve product quality; but in the cooling hopper one is, in order to strengthen transport of solid material, prevent warming plastic sticky jam outlet, two is to ensure the normal work of the transmission part.
Q:Does anyone know the operating procedures for the cable 65+120 extruder?
Operating procedures are based on the preparation of equipment instructions, you can increase some of the preparatory work before the boot, the middle is the operation of equipment instructions, and finally must have safe and civilized operation instructions!
Q:What raw material does the extruder use?
An extruder in which an air vent is disposed at the center of an exhaust extruder to allow removal of air and volatiles from the processed plastic. The main machine of plastic extruder is plastic extruderIt consists of an extrusion system, a drive system and a heating and cooling system. 1. extrusion system extrusion system includes screw, cylinder extrusion die head, extrusion die head, molding parts of the extruder. Also known as extrusion die, extrusion die.

1. Manufacturer Overview

Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range