1. E10,E12,E14, E26,E27,E39, E40 lampholder,series etc.
2. Main material: ceramic/porcelain
3. Professional Manufacturer
4. Metal: aluminium/ iron/ copper/ brass/ stain steel.
5. OEM/ ODM is acceptable
6. We are manufacture, but has the right to handle export business independently.
7. Meet CE/ROHS standard
Porcelain E14, E27, E40 Series etc.
for the lighting accessories
- Q:1000 square meters low voltage.36 volts lighting power supply with multiple transformers and wires
- First of all, make sure your power is too large, but you are not recommended to do so, the cost is too high, the pressure drop is too large, you can raise the voltage to 220V or higher, and then transfer to avoid power losses. If the direct transmission, the power is slightly larger, the line will be very rough, the cost will be very high
- Q:Who knows how big transformers and lines the 36V transformer uses in lighting?
- No matter how many volts the output / input voltage of the transformer is, the size and the amount of the core of the transformer, the wire diameter of the winding lead and the lead thickness must be determined by the transformer capacity. Example: input 220V, output 36V load is 36v/40w light bulb 6, so the primary needs 0.72, secondary use 1.81 diameter enameled wire winding system. The transformer capacity is about 250VA.
- Q:Our power lines and lighting lines are connected to the same transformer. Is there any effect?
- As long as the capacity of the transformer is enough, the voltage fluctuation of the line will be sure to occur when the high power equipment is started. Such fluctuations do not have much impact on the lighting.
- Q:How many 40W bulbs can be brought into the 1000VA lighting transformer?
- Voltage x current = power, in general we are using the total power of 2/3, you can press this type of calculation, if the installation of electrodeless lights, the line should be separated,
- Q:What's the function of the lighting transformer?
- Applies to some requirements for safe voltage 24V - 36V lighting sites. Such as: basement, tunnel, dangerous goods warehouse and so on. Then there is the (mobile, temporary) safety lighting for the overhaul.
- Q:Why can't autotransformer be used as transformer for safety lighting?
- The main and auxiliary coils of the autotransformer have common parts. Once the short-circuit is made, the lighting circuit is directly connected with the high voltage circuit, which is very dangerous
- Q:Why is the two side of the lighting transformer grounded?
- In the three-phase transformer, the neutral point of the three-phase transformer and the metal case are always reliably connected, and the utility model has the advantages of reliable grounding, both working grounding, protection and earthing, and protection of personal safety and equipment safety.
- Q:Is the substation separate from the power and illumination transformer?
- There is only bus in the substation, and the station is connected with the transformer from the bus. If there is no electricity even in the bus, then the substation should not be considered active.
- Q:How to calculate the rated capacity of small transformers for lighting purposes?
- Capacity of power transformer is the basic equipment for a total capacity of [kW] (maximum power consumption rate by a / X100 capacity) divided by the power load [%] value for benchmarking.
- Q:Why the 21 lighting transformer must double winding type safety isolating transformers, prohibited the use of autotransformer.
- The self winding transformer is connected by all its windings, and depends on the position of the sliding contacts to change the magnitude of the voltage. Therefore, there is not only a magnetic connection between the primary winding of the autotransformer (the power circuit) and the two winding (the power supply circuit), but also the direct connection of the circuit. It forms a circuit with the earth, so it can not be used as the power source of the safety voltage
The potential and technology of this production line is still improving. We will be a leader in this industry relying on good designs, high quality materials and strict production.
Our company tries the best to fulfill the requirements from customers. Your satisfaction is our first aim. Our policy is "high quality is priority and good service is the power of growth". We have set up a complete set of after-sales service system.
1. Manufacturer Overview
|Annual Output Value
||US$1 Million - US$2.5 Million
||North America; South America; Eastern Europe; Southeast Asia; Africa; Mid East; Eastern Asia; Western Europe; Central America; Northern Europe; Southern Europe
2. Manufacturer Certificates
|a) Certification Name
3. Manufacturer Capability
||71% - 80%
|No.of Employees in Trade Department
||Below 1,000 square meters
|No. of Production Lines
||OEM Service Offered
|Product Price Range
||Low and/or Average