1) CE,VDE,ISO9001,ROHS approved
2) Main material: porcelain
3) Usage:for the lighting accessories
Porcelain E14, E27, E40 Series etc.
for the lighting accessories
- Q:Who knows how big transformers and lines the 36V transformer uses in lighting?
- 380V-220V/36V transformers, commonly known as safety transformers or line transformers, are mainly used for lighting in shop equipment and mobile lighting for inspection and maintenance. Their power is 50W, 100W, 200W, 300W., and their line size is determined by power!
- Q:Why should lighting transformers be used in factories and mines?
- There are two cases. One is the general factories and mines, and the low voltage is three-phase four wire system, and the neutral point is directly grounded. Between the phase line and the zero line is 220V, which can be connected with the illumination load.
- Q:3 24V100W lights, I need to use a large capacity transformer (220V change 24V)?
- The quality of transformer itself, coupling coefficient, overload capacity, as well as the impact current of the bulb, filament, cold resistance and simultaneous startup factor, it is better to choose the 400VA transformer
- Q:Our power lines and lighting lines are connected to the same transformer. Is there any effect?
- Power lines and lighting lines are connected to the same transformer, without affecting the use of a transformer power users, lighting and power are connected together.
- Q:What transformer can be used in a safety voltage lighting transformer?
- 220V/36V or 24V isolation transformer. Double winding, high and low voltage coils, not connected.
- Q:How many A leakage protection switches are used in 5000VA lighting transformers?
- According to the working principle of the protector, it can be divided into three kinds: voltage type, current type and pulse type. The voltage protection device is connected to the transformer neutral point and the ground, when the electric shock when the neutral point voltage offset to the real estate, in order to make the action to protect the power off, but because it is the protection of the transformer low voltage network, cannot be classified protection, so the power range is large, frequent moves, so has been eliminated. The pulse current protector is a sudden change in the phase and amplitude of the three-phase unbalanced leakage current when an electric shock occurs, which is used as an action signal, but also a dead time. The current type current leakage protector is widely used, so the protector of current type is mainly introduced below.
- Q:Why is the two side of the lighting transformer grounded?
- Single-phase transformer two side lighting to the ground, on the one hand is the lighting products now contain many semiconductor devices such as diodes, transistors, integrated circuits, semiconductor devices vulnerable to electrostatic damage, two side grounding contributes to the surge pressure factors produced by residual electrostatic discharge stay in the main circuit, avoid electrostatic protection, product life. In the 21 aspect, there is distributed capacitance between the two side and the primary side of the power transformer, and the high frequency surge disturbance caused by the primary side current source will directly enter the two side to the main circuit through the distributed capacitor. These unnecessary high frequency interference may jump into the sensitive signal source, make the control system malfunction, and the two side grounding of the power transformer can eliminate most of the undesirable effects of the distributed capacitance.
- Q:How to calculate the rated capacity of small transformers for lighting purposes?
- But in fact, consider the total load, the importance, the location of the machine, and the future additional plan, according to the following order.
- Q:Why the 21 lighting transformer must double winding type safety isolating transformers, prohibited the use of autotransformer.
- Double winding type safety isolating transformer load end and the power supply terminal is not connected, is safe, and autotransformer primary winding of a share, it is directly connected with the power supply end of the power, not safety.
- Q:Can the 500 volt lighting transformer be changed into an electric welder?
- 500 VA transformer should not be used as an electric welding machine, so it is very difficult to reform the system, so it is better to buy a new electric welder
The potential and technology of this production line is still improving. We will be a leader in this industry relying on good designs, high quality materials and strict production.
Our company tries the best to fulfill the requirements from customers. Your satisfaction is our first aim. Our policy is "high quality is priority and good service is the power of growth". We have set up a complete set of after-sales service system.
1. Manufacturer Overview
|Annual Output Value
||US$1 Million - US$2.5 Million
||North America; South America; Eastern Europe; Southeast Asia; Africa; Mid East; Eastern Asia; Western Europe; Central America; Northern Europe; Southern Europe
2. Manufacturer Certificates
|a) Certification Name
3. Manufacturer Capability
||71% - 80%
|No.of Employees in Trade Department
||Below 1,000 square meters
|No. of Production Lines
||OEM Service Offered
|Product Price Range
||Low and/or Average