MILLING TOOTH WIRE STRIPPER HAND TOOLS 702
- Ref Price:
-
- Loading Port:
- Ningbo
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 3000 pc
- Supply Capability:
- 20000 pc/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Specification
MODEL:702
SPEC:8"
QUANTITY PER CARTON(PCS):12/72
G.W./N.W.(KG):19/18
PACK.DIEM(CM):33*25*45
WIRE STRIPPER
Key specification:
1.cut any cleanly strips electrical wire from 10 to 22 gauge
Insert tip of wire into marked holes to determine the size of the wire to be stripped
Squeeze the handle to strip easily and without nicking the wire
2.crimps both insulated and non-insulated ignition terminals
3.tool has black oxide finish for rust resistance
4.Vinyl clad cushion grip handles insulate as well as provide comfort of use
Using the method of the wire stripping pliers
All by hand if the wire stripping pliers groove is then a simple select wire size cut a pull on the line. If and oblique mouth clamp like it by hand, clip to a certain strength, a pull on the line.
Key points:
according to the diameter of the wire, the wire stripper blade aperture
1.According to the thickness of the cable type, select the corresponding stripping knife
2.The cable will be ready in the middle stripping tool blade, to choose a good length of wire stripping
3.Hold the stripping tool handle, cable clip, cable force slowly slowly peeling off the outer skin
4.Loosen the tool handle, then remove the cable, cable metal neatly exposed outside, the rest of the plastic insulation intact.
- Q: Clamp type ammeter; can detect capacitance;
- Pure clamp meter is a measure of capacitors can.Application: usually when the current is measured by an ordinary ammeter, the circuit needs to be cut off. After the stop, the ammeter can be switched in to measure. This is very troublesome, and sometimes the normal running motor is not allowed to do so. At this time, the use of clamp meter is more convenient, the circuit to measure the current is cut off.
- Q: The difference between the inclined pliers and the water nozzle is like the title. Thank you
- The real difference is in their use. Oblique pliers are usually used to cut some hard material.
- Q: Length of wire pliers?
- The commonly used steel clamps are 6, 7, 8, and 1 inches are equal to 25.4 millimeters. In a word, the total length of a pair of pliers.
- Q: When the voltage clamp is used, what is the electrode instability of the current measurement?
- When measuring, the current to be measured should be estimated and the proper range should be chosen. If you can't estimate, you can select a larger number of courses, then reduce the number of files to the appropriate gear. When converting the range gear, it must be done in the case of no electricity or under the opening of the jaw so as not to damage the meter. Three
- Q: Can the clamp type ground clamp clamp the flat iron directly in front?
- Due to the special clamp resistance table structure, so that it can be easily used as a current meter, a lot of this kind of instrument, and has the function of clamp ammeters. On the other hand, the use of a certain frequency signal while the pincer ground resistance meter test to eliminate interference, but the measured cable has great current presence of measurement will be interfered, leading to inaccurate results. Therefore, in accordance with the requirements of the use of the cable should be measured on the current, only when the current is not very large, you can further measure the ground resistance. Some instruments automatically detect noise interference when measuring ground resistance and give hints when interference is too large to measure.
- Q: What's the keel pliers?
- The keel clamp is in a horizontal and vertical keel making pliers
- Q: Tianyu digital multimeter ty3266td clamp can measure DC current it
- A table is set for current transformer and current meter in one meter, is an important branch of digital multimeter, the measured current and current transformer and its working principle is the same. Clamp meter is composed of a current transformer and current meter assembly. The iron core of the current transformer can be opened when the wrench is tightened; the wire through which the current is measured can be cut through the opening of the iron core without cutting off, and when the wrench is released, the iron core is closed. Through the test circuit of the core, the wire becomes the primary coil of the current transformer, in which the current is induced in the two coil through the current. Thus, the current meter connected with the two coil is instructed to measure the current of the line to be measured.
- Q: What is the internal clamp meter sensor?
- The use of electromagnetic current transformer production clamp meterUsing the electromagnetic induction principle, is a kind of special transformer.This can only measure the AC current clamp meter, accurate measurement of sine wave current near 50Hz only, not for direct current measurement
- Q: Do I need to change the brake caliper? How soon will it be replaced?
- General calipers out of the problem is the oil spill, caliper for a new trap can be used, but in general this is a foreign company to buy the repaired with calipers, end braking system is very important, but also because of the bad very little chance, not too much to repair factory supporting tools. Caliper brake oil leaking, less, red brake warning lamp on the instrument of natural light, the driver should immediately find the cause, so suddenly brakes chance is very small, so there is no time or by odometer replace the brake calipers in foreign countries.
- Q: The advantages and disadvantages of clamp brake and disc brake
- Clamp brake: A. is simple in structure, easy to maintain and light in weightB. easily loses the brake force produced by the fingers, especially when the peripheral environment is bad (for example, rain)C. brake time should not be too long, only suitable for low strength use. (for example, it is easy to use the brake when it is downhill for a long time) to make the V brake block burnDisc brake: advantages and disadvantages:The weight of the A. will inevitably be heavier, complex and difficult to maintainB. afraid of greasy dirt, afraid of disc collisionC. is strong enough to adapt to harsh environments
Send your message to us
MILLING TOOTH WIRE STRIPPER HAND TOOLS 702
- Ref Price:
-
- Loading Port:
- Ningbo
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 3000 pc
- Supply Capability:
- 20000 pc/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
