MILLING TOOTH WIRE STRIPPER HAND TOOLS 107
- Ref Price:
-
- Loading Port:
- Ningbo
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 3000 pc
- Supply Capability:
- 20000 pc/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Specification
MODEL:107
SPEC:7"
QUANTITY PER CARTON(PCS):12/120
G.W./N.W.(KG):21/19
PACK.DIEM(CM):38*25*45
WIRE STRIPPER
Key specification:
1.cut any cleanly strips electrical wire from 10 to 22 gauge
Insert tip of wire into marked holes to determine the size of the wire to be stripped
Squeeze the handle to strip easily and without nicking the wire
2.crimps both insulated and non-insulated ignition terminals
3.tool has black oxide finish for rust resistance
4.Vinyl clad cushion grip handles insulate as well as provide comfort of use
Using the method of the wire stripping pliers
All by hand if the wire stripping pliers groove is then a simple select wire size cut a pull on the line. If and oblique mouth clamp like it by hand, clip to a certain strength, a pull on the line.
Key points:
according to the diameter of the wire, the wire stripper blade aperture
1.According to the thickness of the cable type, select the corresponding stripping knife
2.The cable will be ready in the middle stripping tool blade, to choose a good length of wire stripping
3.Hold the stripping tool handle, cable clip, cable force slowly slowly peeling off the outer skin
4.Loosen the tool handle, then remove the cable, cable metal neatly exposed outside, the rest of the plastic insulation intact.
- Q: What is the DC clamp meter measuring principle
- Since there is a magnetic field around the current and is proportional to the magnitude of the current, it is possible to know the magnitude of the current as long as the magnetic field is detected.
- Q: What is the holding technique of sterile holding forceps in proper nursing operation?
- Thumb and ring fingers holding forceps. Bend downward, close and take out. Non contact bottle wall
- Q: Use clamp ammeters, which should pay attention to security matters?
- When measuring, wear insulated gloves and wear insulating shoes. When observing the value, pay special attention to keeping enough distance between the human body and the live part.
- Q: A digital multimeter, how the quality of measuring capacitance
- Some digital multimeter has the function of measuring capacitance, the range is divided into 2000p, 20n, 200N, 2 and 20 ~ 5. When measuring, the two pin of the discharged capacitor can be directly inserted into the Cx jack on the table board, and the display data can be read after the proper range is selected.
- Q: Survey work should pay attention to what use clamp meter?
- When measuring the phase current of high voltage cable, the distance between the cable head and line should be more than 300mm, and the insulation is good, and the measuring convenience can be carried out. When there is a grounding in the three-phase, it is strictly forbidden to measure.The 7. clamp meter should be stored in a dry room, when used to wipe clean.
- Q: How to use the chain tongs water pipe forceps chain tongs
- The chain pipe clamp, pipe clamp is a special tool for rotating circular member, because the circular component is no shoulder armor, with chain tongs or pipe clamp rotation is carried out by extrusion method to belong to the chain pipe wrench in use is the chain around the circular members a week, with the rod hanging hook in the opposite direction to the chain around the pressure bar, then the chain will pay close attention to the circular component rotation
- Q: Can the clamp type ground clamp clamp the flat iron directly in front?
- Due to the special clamp resistance table structure, so that it can be easily used as a current meter, a lot of this kind of instrument, and has the function of clamp ammeters. On the other hand, the use of a certain frequency signal while the pincer ground resistance meter test to eliminate interference, but the measured cable has great current presence of measurement will be interfered, leading to inaccurate results. Therefore, in accordance with the requirements of the use of the cable should be measured on the current, only when the current is not very large, you can further measure the ground resistance. Some instruments automatically detect noise interference when measuring ground resistance and give hints when interference is too large to measure.
- Q: What's the line clamp?
- If you want to remove the wire sheath. Then choose the location of the corresponding wire peeling. There are many models behind the pliers. Go to 1 squares, 2 squares, and so on.. Put it in the corresponding position, press the pliers, pull out the wire and peel it.Press the clamp behind the rotating shaft is to press the metal connector, choose the corresponding model, put it in it..If you are a cable clamp, it's basically the same. Very simple.
- Q: Which brand of nail clippers is good? Nail clippers ten brands
- I think Vivtorinox is good. Maybe I'm more superstitious about his family's knives, so I feel good.
- Q: Is the nose pliers the same as the water jet pliers?
- Not the same, the nozzle blade is thin, relatively sharp, can only cut thin copper wire and plastic, rubber and other materials, cut the copper wire after the incision is flat.
Send your message to us
MILLING TOOTH WIRE STRIPPER HAND TOOLS 107
- Ref Price:
-
- Loading Port:
- Ningbo
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 3000 pc
- Supply Capability:
- 20000 pc/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
