Q:Aluminum alloy door window frame and the wall hole gap is too large how to deal with

With a blowing agent into the gap, you can make it full of foam, up to the sealing effect

Q:How do I paint my brown exterior metal door white?

Lightly sand door with a fine grit sand paper (this is needed so that the paint has a surface on which it can cling to. Wipe of dust and let dry. Spray paint primer made for metal. Once dry, spray paint desired color. I have been using spray paint a lot more lately and find it goes on easier and looks nicer than painting on color. I use it when I paint furniture.

Q:Aluminum alloy doors and windows how the amount of glass size

The mouth minus 7 mm, the mouth is the pressure line that position, without pressure inside the mouth minus 3 mm, like the specific point can be said that your phone number I call you, I do the doors and windows

Q:How do I pull the rivet out of my house?

Hand drill down just fine, and generally aluminum alloy doors and windows with a 4 mm diameter rivets, you choose 4.2 mm brick just fine,

Q:Titanium magnesium alloy door and solid wood composite door which expensive

Solid wood composite expensive, a Tang 1 thousand 12, titanium magnesium alloy generally also 7,8 hundred

Q:Aluminum alloy door and window frame and hole wall gap for how much, in the specification can be found

The gap between the door frame and the hole is required Wall facade material between the door and window frame and the hole between the gap Water wall 15mm, mortar + coating 20 ~ 25mm. Bricks 25 ~ 30 mm. Stone 40 ~ 50mm (using concrete mouth or increase the sub-box) outside the insulation wall External insulation thickness + Facing material practice gap -10 Note: (1) due to the finishes (including insulation) material thickness requirements, will make the window frame and the hole between the gap increases, when the door When the gap between the window frame and the hole is greater than 35mm, it is necessary to add a concrete mouth or steel sub-frame between the door frame and the hole. The gap between the mouth and the window frame should not be greater than 20mm; sub-frame and the gap between the doors and windows frame is 5mm, sub-frame and the hole side of the gap should not be greater than 20mm; no sub-frame when the finish surface to be pressed window frame 5mm , There are sub-frame when the surface and sub-box top flush. (2) The gap between the threshold of the door frame and the hole shall be adjusted according to the difference between the floor material and the threshold of the door frame. To ensure that the gap between the threshold and the floor (wall) filled with dense and external waterproof integrity, after the completion of the floor of the floor should be high outside the low

Q:What are the characteristics of red apple aluminum doors and windows?

Never heard of red apple aluminum windows and doors! But aluminum doors and windows are good!

Q:What are the characteristics of aluminum doors and windows?

Plastic doors and windows are different from the prominent features of aluminum doors and windows are two different materials, steel doors and windows aging is brittle, aluminum aging is oxidation.

Q:Aluminum alloy doors and windows 5 +6Ar +5 +6Ar +5 What does it mean

Ar refers to a double hollow glass of nitrogen or argon 5mm glass + 6mm aluminum spacer

Q:Aluminum alloy door how good material and good

1, thickness: the thickness of the material 2, the strength: tensile strength should be up to 157 Newton per square meter, yield strength to reach 108 Newton per square millimeter. When buying aluminum doors and windows, you can use the hand to bend the profile, after the release should be able to recover. 3, color: the same aluminum alloy color should be consistent, such as color is obvious, that should not buy. 4, flatness: check the aluminum alloy surface, should be no depression or bulging. 5, gloss: aluminum doors and windows to avoid the purchase of the surface to open the bubble (white) and ash (black spots), and cracks, burrs, leather and other obvious defects in the profile. 6, the degree of oxidation: oxide film thickness should reach 10 microns. Optional aluminum doors and windows can be drawn in the profile surface, look at the surface of the oxide film can be erased.