LPG Forklift Truck (Nissan engine, 3.0Ton)
Type:Powered Pallet Truck
Load Capacity:1T - 5T
Min. Turning Radius:2470
Min. Width of Right Angle Stacking:4280
Min. Width of Right Angle Channel:2120
Origin:Qingdao City, Shandong
Production Capacity:10000 PCS/Year
1, Standard configuration
Load capacity: 3000kg
Load center: 500mm
Lift height: 3-6.5M
Engine type: NISSAN K25
CST Penumatic tires
2, Mast available
2 stage from 3.0m to 5.0m
2 stage FFL from 3.0-5..0m
3 stage FFL from 4.5-6.5m
3, Engine available
Name: NISSAN K25
Original: Made in Japan
Rated H.P.: 38KW/2300rmp
Max. torque: 177N.m/1600rpm
|1||Characteristics||Fuel type||LPG & Gasoline|
|5||Full free lift height||mm||135|
|7||Mast tilting angle||Front/Rear||Deg.||6/12|
|8||Min. turning radius||mm||2470|
|9||Min. width of right angle|
|10||Min. width of right|
|12||Overhead guard height||mm||2120|
|14||Performance||Max. travel speed||Full load||km/h||19|
|15||Max. lift speed||Full load||mm/s||460|
|16||Max. traction power||Full load||KN||20|
|Dimensions||Total length||With fork||mm||3805|
|18||Total length||Without fork||mm||2735|
|20||Mast extended height||mm||4265|
|21||Mast lowered height||mm||2040|
|28||Motor||Model ||ISUZU C240|
|30||Rated torque ||N.m/r.p.m||137.7/1800|
|33||Fuel tank capacity||L||70|
|35||Operating pressure ||Mpa||18.5|
- Q:The basics of driving a forklift
- Adjust the distance of the cargo fork according to the volume and shape of the goods, and make the right and left fork force even. When taking the cargo or pallet, the fork should be inserted at the insertion hole level of the pallet, avoiding the collision as much as possible, and then the fork of the cargo after the cross, and then the door frame. Before you start, look around the forklift and the cargo stacking and keep the fork from 20 to 30 centimetres above the ground to prevent the cargo from falling. The whistle should be sounded when entering or turning.
- Q:The repair process of forklift inspection
- Forklift maintenance and overhaul procedures In order to keep the forklift in good condition, the main points of the maintenance work are summarized. The maintenance and maintenance of forklift truck is divided into two kinds: maintenance on demand and maintenance on a regular basis.
- Q:What are some of the common failures of forklifts?
- First, if the generator is normal, if the generator is normal then it is the problem of the battery. The most stupid way to measure the virtual voltage of a direct battery is to charge the battery with a charger, and if it can't be plugged directly, the battery will be dead. Change generators or batteries. When you turn on the key switch, you turn on the key switch and start clicking. Change the starter 3, if the key switch is bad, start with a little bit of reaction fluid. In the key switch 4, the oil pump is not supplied with oil and this needs to be removed and sprayed. In exchange for oil pump or repair. There is no oil in the tank. Come on! There is no oil measuring tape. Add oil! 7 and 8, twist the key switch, and the motivation is normal, but you can't afford a car, or get up and stall. Repair engine!
- Q:How to drive a forklift
- Maintenance of words All you have to check good oil daily These can be the dalai And to a certain range to wash the change of the change of the wash everything OK the dalai
- Q:Where are the advantages and disadvantages of a battery lifter and a diesel forklift
- Introduction and comparison of electric forklift truck and internal combustion forklift truck In order to understand the structure of forklift and its working principle, the two kinds of forklift truck are analyzed, and the advantages and disadvantages are given. The overall structure of the forklift truck There are a wide variety of forklifts, but no matter that type of forklift, it is basically made up of four parts: (1) the power part. Power for forklift truck, usually in the rear of the forklift truck, and the balancing act. (2) the chassis. Take the power of the power plant, make the forklift move, and make sure it walks properly. (3) the working part. For fork and lift. (4) electrical equipment.
- Q:Which is better, solid forklift tyres and inflatable forklift tyres?
- Cons: tires are harder and harder to bump Like, the installation is troublesome, the process is much, if the installation is not good still can cause the tyre and the rim to skid.
- Q:After the forklift is killed, it will stall!
- Domestic forklift would ', that can not, there is nothing wrong with the car, I didn't see any domestic had such a situation, or diesel pump is broken, lead to the low idle speed, low (but the oil pump is normal, idle will not necessarily shut down), or steering cylinder oil seal is damaged, steering on each bearing damage, often do not beat butter, causing friction is too large, resulting in the stress, remove from heat. It is recommended to be repaired on all parts, more butter, high idle, or school oil pump
- Q:How many years can you use a forklift battery
- The battery will produce the gas during the charging process, should keep the charging area ventilated well and there is no open fire. 4, in any case, in the process of charging the electrolyte temperature should not exceed 45 ℃, otherwise should try to cool down, such as to reduce the charging current, measures such as artificial cooling or pause charge, after waiting for the temperature drop charge again. It is strictly forbidden to put metal tools on the battery. There is no excess clutter on the battery.
- Q:A manual forklift oil leak, what if you can't get up?
- Oil leakage between body Because working oil, oil spill, oil return tao tao throughout the three monolithic between the valve body, valve body between the sealing requirements are, therefore, between the body and body oil duct installation O ring after bolting the body on the camera, to achieve the purpose of sealing. If the fastening torque of the bolt is different, it may result in the body warping. If the installation as the body damage or o-ring aging or damage, in the role of oil pressure, the valve body between the internal leakage are apt to happen. Repair, if the body damage criterion need to grinding, change the O ring, and screw down the bolt according to the requirements of sequence and torque.
- Q:How about the forklift truck training, the forklift wages
- What about the salary for a forklift truck? That's a question everyone wants to know about the forklift industry. Or ask a friend, or surf the Internet baidu once, with the rapid development of economy in recent years, an increasing demand for forklift worker, forklift worker treatment of linear growth, more and more people into forklift industry, forklift worker to the person's education is not high, is a technical work, stable work, family, not like other work extensively world run, salary is low, don't know which day to go home the wife had run away with people
1. Manufacturer Overview
|Annual Output Value
2. Manufacturer Certificates
|a) Certification Name
3. Manufacturer Capability
|No.of Employees in Trade Department
|No. of Production Lines
|Product Price Range