Gate Valves From China Largest Valve Manufacturer
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 50 pc
- Supply Capability:
- 5000 pc/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Characteristics:
Gate valves are the traditional product.
They are widely used on the system piping in the industries like petroleumn, chemical, paper, hydropower, ship building, water supply & discharge, energy etc., and applicable to lots kinds of gases, liquids, semi-fluids and solid powder medias.
Technical Data:
Normal Pressure: 1.0MPa/1.6MPa
Shell Test Pressure: 1.5MPa/2.4MPa
Sealing Test Pressure: 1.1MPa/1.76MPa
Applicable Medium: Oil Gas Water
Technical Specifications:
Design: DIN3352
Face to face: DIN3202-F4
Flange drilling: DIN2531 / DIN2532 / DIN2533 / EN1092-2
- Q:Internal screw current limiting gate valve (Tan Gang) PN5.0 DN15/ Phi 1 Rc1/2 what does that mean?
- We did thatInternal thread current limiting gate valve (Tan Gang)Body material: carbon steelPressure rating: PN5.0 = 300LB American StandardNominal = DN15 = 1/2"Phi 1 = in the middle of the gate drilling a Phi 1 hole, so that in closing there will be a certain flow, that is, the minimum flow, that is, the current limit.Rc1/2 is thread, which is the connection
- Q:what are their applicable conditions? Advantages and disadvantages?
- Valve is closed parts (RAM) along the vertical axis of the mobile channel valve in the pipeline, used primarily as a medium cut that open and close, generally do not have to do with traffic regulation, it can be used for low temperature and low pressure can also apply to high temperature and high pressure, and according to the different valve material for different media. In various types of valves, gate valve is the most widely used.Advantages: low fluid resistanceSmall torque required for opening and closingYou can use the ring road in which the medium flows in the two direction, that is to say, the medium is free of flowWhen fully open, the sealing surface is less eroded by the working medium than the cut-off valveThe structure is simple and the manufacturing process is betterThe structure length is shortDisadvantages: the overall size and opening height are larger, the space required for installation is also largerIn the process of opening and closing, there is relative friction between the sealing surfaces, and wear more easily, and even cause friction at high temperatureGeneral gate valve has two sealing pairs, to the processing, grinding and maintenance increased the number of difficultiesLong opening and closing time;
- Q:What does gate valve DN80-PN16-QT450 mean?
- DN80 means: liquid, internal thread connection, the valve sealing surface material for rubber, seat sealing surface material for lining adhesive, nominal pressure of 10 kg / cm2, nominal diameter of 80mm Iron Butterfly valve.
- Q:What is the Z15T-16C letter of the gate valve?
- The Z class code indicates the type of gate valve, gate valve is the first letter of the alphabet. The gate is manual driving mode, 1 said the connection form of gate valve for connecting thread, 5 represents the structure form of gate valve for rigid single gate, T gate said lining material of copper alloy, 16 PN1.6MPa nominal pressure valve. C said the valve body material is carbon steel.
- Q:Does the tap belong to a stop valve or a gate valve?
- When the valve is installed, the medium can enter from the bottom of the valve core and enter the two way from the top. Medium from the spool into the advantages of the valve closed when the packing is not under pressure, can extend the service life of the packing, and can be pressure in front of the valve in the case of replacement of packing work. Medium from the spool into the bottom of the shortcomings of the valve driving torque is larger, about 1.05~1.08 times above the entrance, the stem by the axial force of large, easy to bend the stem. To this end, the media from below to enter the way, generally only applicable to small caliber manual stop valve, to the valve closed, the media acting on the spool of force is not greater than 350kg limit. Electric cut-off valve is generally used to enter the media from the top way. The disadvantage of the medium entering from the top is just the opposite of the way it is entered below.Compared with the gate valve, the utility model has the advantages of simple structure, good sealing performance, and convenient manufacture and maintenance. The disadvantage is that the liquid resistance is large, and the opening and closing force is large. Gate and globe valves are fully open closed type valve, cut off or connected as the medium use, not as a control valve.The range of application of stop valves and gate valves is determined by their characteristics. In the smaller passages, the cut-off valve is used when required for better shutoff; in the steam pipe and the large diameter water supply pipe, the gate valve is generally used because of less fluid resistance.
- Q:What is the difference between a flanged gate valve and a wire gate valve?
- This is very simple, flanged gate valve is the valve with both ends of the flange, the installation of the pipe to weld the reverse flange, bolt with the pipe flange and valve flange connection. Valve is the valve ends with wire wire, a wire and wire points, and pipeline installation, connecting part with joint or head of the screw and the valve directly on the pipe screw connection.
- Q:What is the difference between an elastic gate valve and a rigid gate?
- Brief introduction: the valve gate valve is a gate opening and closing parts, RAM direction of motion perpendicular to the direction of the fluid, valve can only be fully open and fully closed, can not be adjusted and the throttle. Gate has two sealing surface, the most commonly used mode gate valve of the two sealing surface to form a wedge, wedge angle with valve parameters vary, usually 50, medium temperature is not high when 2 degrees 52'.Wedge gate valve can be made into a whole, called the rigid gate; can also be made to produce micro deformation of ram, in order to improve its process of deviation, make up the sealing surface angle in the process, the gate is called the flexible gate.
- Q:The legend of gate valve and stop valve
- The working principle is different. The stop valve is an upward stem type, and the handwheel rotates and rises with the stem. Valve is hand wheel rotation, stem upward movement. Flow is not the same, the gate valve requires full open, the cut-off valve is not the same. The gate valve has no inlet and outlet direction requirements, and the cut-off valve has the required inlet and outlet!Gate valve and stop valve are shut-off valve, is the most common two valves.From the exterior, the gate valve is shorter than the cut-off valve, especially the bar valve needs a higher height space. Valve sealing surface has a certain degree of self sealing capacity, its spool depends on the media pressure tight contact with the valve seat sealing surface, to achieve tight leakage. Wedge gate valve spool angle is generally 3~6 degrees, when forced to shut down excessive or temperature changes of the valve core is easy to die. Therefore, high temperature and high pressure wedge gate valve, in the structure have taken certain measures to prevent spool stuck. The valve in the opening and closing valve and valve seat sealing surface contact and mutual friction is always so easy to wear sealing surface, especially in close off the valve, the valve before and after the great pressure, sealing surface wear is more serious.
- Q:What kind of valve is gate valve? Is it different from the cut-off valve?
- Gate valve and the role of the cut-off valve, are playing a role in isolation. The difference is that the gate valve and the cut-off valve are constructed differently. Fluid from the gate valve flow and flow direction is straight, there is no change in direction, but in the cut-off valve is from the bottom of the valve flow into the flow from the upper part of the spool.
- Q:Why can't the pressure measuring point be set at the two ends of the gate valve when measuring the resistance loss of the gate valve?
- the valve before the pressure measuring point, distance of valve straight pipe length is 5 times the diameter of the valve after the pressure valve, the distance is 10 times the diameter of straight pipe length.
1. Manufacturer Overview |
|
---|---|
Location | |
Year Established | |
Annual Output Value | |
Main Markets | |
Company Certifications |
2. Manufacturer Certificates |
|
---|---|
a) Certification Name | |
Range | |
Reference | |
Validity Period |
3. Manufacturer Capability |
|
---|---|
a)Trade Capacity | |
Nearest Port | |
Export Percentage | |
No.of Employees in Trade Department | |
Language Spoken: | |
b)Factory Information | |
Factory Size: | |
No. of Production Lines | |
Contract Manufacturing | |
Product Price Range |
Send your message to us
Gate Valves From China Largest Valve Manufacturer
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 50 pc
- Supply Capability:
- 5000 pc/month
OKorder Service Pledge
OKorder Financial Service
Similar products
New products
Hot products
Related keywords