Q:What is the difference between the model z81x-16q and z81x-16c of the groove gate valve?

Not 16qIs 16p, the former body is stainless steel, and the latter body is carbon steel

Q:Gate valve, butterfly valve, ball valve advantages and disadvantages? What are the usual valves?

Stop valve: a valve that closes the valve and moves along the center line of the valve seat. According to this form of valve movement, the valve seat opening change is proportional to the valve stroke. Because of the valve stem to open or close the trip is relatively short, but very reliable cut off function, and because changes in the valve seat and the valve stroke is proportional, is very suitable for flow regulation. Therefore, this type of valve is very cooperative for cutting or regulating and throttling.Advantages: in the process of opening and closing, because the friction between the valve and the sealing surface of the valve body is smaller than that of the gate valve, the utility model has the advantages of wear resistance. Second, the opening height is generally only 1/4 of the seat channel; therefore, it is much smaller than the gate valve; usually there is only one sealing surface on the valve body and the disc; therefore, the manufacturing process is better and the service is easy to maintain. Because its packing is generally a mixture of asbestos and graphite, it has a higher temperature resistance. Steam valves are normally used with stop valves.Disadvantages: as a result of the medium through the valve flow direction has changed, so the minimum flow resistance valve is higher than most other types of valves; second, due to longer travel, opening slower than the ball.

Q:Please tell the specific specifications and specifications of the gate valve and advise the principle of management cooperation Thank you

Please tell the specific specifications and specifications of the gate valve and advise the principle of management cooperation Thank you

Q:What's the meaning of flexible z45x-10q door valve?

Crown valve pressModel Z45X-10QZ refers to gate valve4 finger flange connection5 refers to the dark bar driveX refers to rubber seals10 refers to 10 kg pressureQ refers to the body material, ductile ironFull bore flange soft sealed gate valve

Q:Stainless steel gate valve DN150 200300 weight, who knows?

Valve selection of different driving methods, connection forms, structural forms, nominal pressure, sealing surface materials, lining materials, valve body material will affect the weight of the gate valve more or less, it can not be generalized.Take my commonly used Z41H-16P (i.e. PN1.6MPa) series stainless steel gate valve as an example, and the weight of DN150/200/300 is 134/192/379kg. Of course, different manufacturers may vary in weight, but not much.I hope I can help you.

Q:Why does the fire hydrant box in the air defense area need to be added with gate valves?

when the envelope from the introduction of civil air defense, air defense should be set in the side of retaining structure; through the protection unit between the closed wall, should be installed in the pipe walls on both sides of the door closed;2 protection valve nominal pressure shall not be less than 1.OMPa;

Q:Does the tap belong to a stop valve or a gate valve?

When the valve is installed, the medium can enter from the bottom of the valve core and enter the two way from the top. Medium from the spool into the advantages of the valve closed when the packing is not under pressure, can extend the service life of the packing, and can be pressure in front of the valve in the case of replacement of packing work. Medium from the spool into the bottom of the shortcomings of the valve driving torque is larger, about 1.05~1.08 times above the entrance, the stem by the axial force of large, easy to bend the stem. To this end, the media from below to enter the way, generally only applicable to small caliber manual stop valve, to the valve closed, the media acting on the spool of force is not greater than 350kg limit. Electric cut-off valve is generally used to enter the media from the top way. The disadvantage of the medium entering from the top is just the opposite of the way it is entered below.Compared with the gate valve, the utility model has the advantages of simple structure, good sealing performance, and convenient manufacture and maintenance. The disadvantage is that the liquid resistance is large, and the opening and closing force is large. Gate and globe valves are fully open closed type valve, cut off or connected as the medium use, not as a control valve.The range of application of stop valves and gate valves is determined by their characteristics. In the smaller passages, the cut-off valve is used when required for better shutoff; in the steam pipe and the large diameter water supply pipe, the gate valve is generally used because of less fluid resistance.

Q:Which is more expensive, bronze gate valve or brass gate valve?

The advantage of casting method is more obvious. The casting of stainless steel is much more difficult than that of brass.

Q:What are the differences between the gate valve and the cut-off valve?

Is the gate valve opening and closing parts, RAM direction of motion perpendicular to the direction of the fluid, valve can only be fully open and fully closed, is not suitable for regulation and throttle. The gate has two sealing surfaces. The two sealing surfaces of the most commonly used wedge gate valves form a wedge. The wedge angle varies with valve parameters, usually 5o. Wedge gate valve can be made into a whole, called the rigid gate; can also be made to produce micro deformation of ram, in order to improve its process of deviation, make up the sealing surface angle in the process, the gate is called the flexible gate. Valve closed, the sealing surface can only rely on medium pressure to seal, that is to rely on medium pressure to the gate sealing surface pressure to the other side of the seat to ensure the sealing surface seal, which is self sealing. Most of the valve is forced seal, that is, when the valve closes, to rely on external force to force the gate to the seat, in order to ensure the sealing surface sealing.A stop valve is a valve that closes the valve and moves along the center line of the valve seat. According to this form of valve movement, the valve seat opening change is proportional to the valve stroke. Because of the valve stem to open or close the trip is relatively short, but very reliable cut off function, and because changes in the valve seat and the valve stroke is proportional, is very suitable for flow regulation. As a result, this type of valve is ideal for use as a shut-off or regulator and throttling

Q:What does the gate valve SZ45X-1.0 stand for?

Z- stands for gate valves, 4 for flange connections, 5 for wedge wedge single gate, X for rubber seals, and 1.0- for PN1.0MP