Q:Butterfly valve model D373F-16C, ask God answers

D butterfly valve, 3 turbo rotating, 7 pairs clip type, 3 eccentric F PTFE seal, 16 nominal pressure 1.6MPA, C valve body material, carbon steel

Q:valve adjustment 2001 chev prism 1.8L

valve adjustment . you need to know the fire order. the gage between the stem. rotators the cranshaft. it could be cold start. cylinder need to be bottomed center.

Q:That industry uses most of the butterfly valve, and only use the butterfly valve, a large number of use of butterfly valve, seek expert advice!

Large diameter heating pipes with more than butterfly valves, greater than or equal to DN600 are used butterfly valve

Q:Butterfly valve D41W-1, 41, W, 1, respectively, what does that mean?

This butterfly valve in our factory called butterfly, 4 represents the connection of the flange connection flange is French, 41 in 1 on behalf of butterfly valve, W represents the body seal, is C that is actually the correct type of cast steel, should be D41W-1C. Suitable for ventilation, smoke, and these media.

Q:How is the lug butterfly valve connected to the flange?

Lug type butterfly valve is also called a single flange type, that is, with a flange on the valve body, usually installed at the end of the pipe, and even the method is 1: double bolt lock on the valve body 2: into the flange 3: lock nut

Q:In the pipeline attached building Atlas 05S502, in the middle of a water meter and check valve, the two sides are divided into two butterfly valve, want to ask why to arrange this way, what is the role of the two butterfly valve?

Check the water gauge and check valve on both sides to facilitate the maintenance and replacement of water meter and check valve.

Q:What is the meaning of the D341*5-10 / 16ZB1 turbine butterfly valve flange said?

Liu1964tg, this guy is right, don't know, don't mislead everybody

Q:Hey YA! I am looking at getting an 01 Honda Prelude this month and valve adjustment keeps coming up when people discuss this car and other cars as well. What is this? Does it cost a lot to do, and is it important? Thank you!

An import shop can probably do this in two hours and cost should be in the general range of $200-300 I'd estimate. There is a camshaft that acts on the valves, and there is a predetermined amount of play or slop in the system that is within specs. As the valve seat wears, the valve gets pulled further into the head, and this lessens the play as it wears. If it gets too tight and fails to have any play, the valve won't be held tight against the seal and it will leak, lose power and possibly burn the valve. So yea, get it set. Also may want to factor in timing belt cost and ask about that and water pump as those aer replaced together.

Q:Transformer butterfly valve and pressure relief valve difference

The butterfly valve is usually fitted with an oil immersed transformer between the tank and the radiator to control the flow of oil between the transformer tank and the heat sink. When large power transformers are delivered, the radiators are usually individually packed to reduce transport sizes. The butterfly valve is closed to prevent the outside air or water from entering the transformer tank. When the transformer is transported to the installation site, the radiator is installed on the butterfly valve one by one. When the radiator is installed, the butterfly valve can be opened so that the oil flow between the transformer, the oil tank and the radiator can be circulated, so as to play the role of heat dissipation.When the transformer is running, it is found that when the radiator has seepage, the butterfly valve can be closed to avoid further leakage of transformer oil, and a new radiator can be replaced.

Q:How to calculate the size of the manual butterfly valve?

1. The size of the installation fits only two: the length of the structure and the distance between the flanges.2, butterfly (Manual butterfly) butterfly plate installed in the pipe diameter direction. In the butterfly valve body cylindrical channel, the disc shaped butterfly plate revolves around the axis, the rotation angle is 0 degrees -90 degrees between, when rotates to 90 degrees, the valve opens the card completely. Butterfly valve structure is simple, small size, light weight, only by a few parts. The utility model can be rapidly opened and closed only by rotating 90 DEG, the operation is simple, and the valve has good fluid control characteristics. When the butterfly valve is in the fully open position, the butterfly plate thickness is the only resistance when the medium passes through the valve body, so the pressure drop produced by the valve is very small, so the flow control characteristic is better. Butterfly valve has an elastic seal and metal seal, two types of seals. Resilient sealing valve. The sealing ring can be mounted on the valve body or attached to the periphery of the disc.