Q:How to connect the signal butterfly valve?

The signal butterfly valve should be the surveillance and alarm of human action. Once it is closed, it will alarm the system.Signal butterfly valve wiring method:1, open the switch box cover, according to the electrical control requirements, the cable core line to the corresponding terminal, and sealed cable imports, while the cable fixed, to prevent external force damage when the cable wiring.2, when the valve in the "closed" position, the clockwise rotation of the following relationship to the cam is just touch micro switch cam (you can hear the clicking sound), and then tighten the screw on the cam cam.3, when the valve in the "fully open" position, counterclockwise turn the upper open cam, with the same method to adjust the open cam.4, adjust the limit screw, when the valve in the "full off" or "open" position, should not make the limit screw just at the top of the worm gear limit plane, and should have a certain gap, and then tighten the lock nut on the screw.5, on the cover of the electrical switch box cover, when the valve in the "off" position, the pointer opening indicator to dial "0" scale, and tighten the screws pointer.

Q:Three eccentric hard sealing butterfly valve, why not fit in the end of the pipe?

The sealing ring will hold up. It does not fit in with the flange end of the pipeline, this addition is the most common and convenient pipeline after purge and easily add pipeline.

Q:Butterfly valve, two-way pressure and one-way pressure what is the difference?

The positive pressure and the reverse pressure, the pressure when the medium returns

Q:What's the difference between butterfly valves and check valves?

Butterfly valve is manual, only switch function.The check valve is an automatic valve, which prevents backflow of the pipe medium.

Q:1988 volkswagon cabriolet, rabbit tried mystery oil let sit for a week having trouble with stuck valves even taken a wrenrch to manually unstick. help any suggestions 4 cyclinder car has been sitting up for about 4 years

The only reason for a stuck valve is if it bent from a thrown timing belt. Sitting 4 years will not cause valves to stick usually, because there is always some oil leakage from the head, that prevents rust. How do you know the valve is stuck? Have you done a compression test, checked the valve clearance? When you say you take a wrench to manually unstick it, it would help to know what you mean, because there is no place to put a wrench that would help unstick a valve that was stuck. You need to tell us much more.

Q:I have a 1993 Oldsmobile Cutlass Supreme and I think I have the case of the blow-by. The engine had high mileage, but was rebuilt b/c it stalled while driving. 3.1L V6 gasoline engine. The fuel filter and the fuel pump are brand new. Now we have the same problem a few months later. It stalls while driving. Its been sitting a while and won't start by itself, so I pulled off the air intake hose off of the air filter to spray starting fluid into it. I noticed oil puddled in the air intake hose, so I looked for the PCV valve on the rocker cover. There is a tube going from the air-intake hose to the rocker cover. I popped out the tube from the rocker cover and there is no PCV valve. Just tube. Is that where the PCV valve is supposed to go? If not, where can I find it on the engine? And could that possibly fix the blow-by and the stalling engine? I'd appreciate any help. Thanks in advance.

top of the manifold

Q:Are fire fighting signal valves and signal butterfly valves the same thing?

The same nature: both can open and close, there is also information back fed.Signal valves are collectively referred to as signal butterfly valves.

Q:When will Butterfly Valves be used?

Butterfly valve is the most common and most widely used in the field of the valve, cases of sewage treatment, water supply, iron and steel, building construction and heating fields needs a lot of valves, especially with the hard seal butterfly valve butterfly valve position and a lot of popularity, the field is used more widely.

Q:What do you mean, handle, butterfly valve, hard back and soft back?

The butterfly valve of the handle butterfly valve is installed in the direction of the diameter of the pipe. In the butterfly valve body cylindrical channel, the disc shaped butterfly plate revolves around the axis, the rotation angle is between 0 degrees -90 degrees, when rotates to 90 degrees, the valve is fully open. This valve is mounted horizontally.Butterfly valve has an elastic seal and metal seal two types of seals. Resilient sealing valve. The sealing ring can be mounted on the valve body or attached to the periphery of the disc.The hard back is the metal seal, and the soft back is the elastic seal.

Q:What's the difference between D71X-16 and D71H-16 butterfly valves?

Model D71X model means this, D represents butterfly valve, 7 represents butterfly connection form for clip type connection, 1 represents straight through, and 16 represents pressure 16 kg pressure.X stands for sealing and soft sealing, and the sealing surface is usually nbr.H stands for metal hard sealing, usually 2Cr13 surfacing.D71X-16 butterfly valve featuresIts main features are:1 、 the design is novel, reasonable, unique structure, light weight, fast opening and closing.2 、 small operating torque, easy operation, labor-saving and smart.3. It can be installed and maintained conveniently in any position.4, seals can be replaced, sealing performance is reliable, to achieve two-way sealing, zero leakage.5, sealing materials aging resistance, corrosion resistance, long service life and so on.